Activity in Technology and Support
DNA inaccessible
I have problem with DNA center I can't access " DNA " site inaccessible
EAP packets to MAC addresses of VMware VMs are also reacted to by the
A Windows 11 host 24H2 with active 802.1x on the LAN, installed VMWare Workstation and VMs that use the host LAN adapter in bridge mode responds to EAP packets from the switch that are sent to the MAC address of the VM. Why? As a result, the host its...
Nexus Dashboard 4.1(1g) - API Browser (Swagger) Missing Endpoints?
Hi, I'm trying to do some development work against the latest ND release. I notice that in this version there are very few endpoints listed under "Manage" - including some of the basics like VRFs and Networks. Where should I be looking for these ...
How to put c-edge sdwan router in cli mode
I have a router and both isp link down and now router is unreasonable and wanted console but is it possible we can configure it via console as isp needs to change wan ip.
PBR policy
I need to forward all traffic come to port 1 to LTE card and all traffic comes to port port 2 to exit VDSL card, how to do that?
Configuring SNMP Traps for Cisco FMC
Hi everyone! I was able to configure the SNMP port 161 on the FMC via GUI. But I cannot seem to find the SNMP Traps configuration. Below I managed to check in FMC CLI , but I am stuck on how I will implement them and make my FMC send traps to our SNM...
Wireless migration CBW
Hello Team,This may be a basic question, but I would kindly like clarification. If I currently have an older WLC 2500 and wish to migrate to CBW for a small business environment, where the existing WLC has three interfaces configured under the contro...
TLS 1.3 for tacacs and http service
testing tls1.3 for http and tacacs services on 9300-48U with 17.15.3 http is fine but I don't see tls option under tacacs server config switch(config-server-tacacs)#t?timeout any advice is appreciated, I have my root and signed certificate associated...
Migration using FMT with different FMC
Hello everyone, I’m currently performing a migration from Cisco ASA with FirePOWER Services (ASA + SFR) to Cisco FTD using the Secure Firewall Migration Tool (version 7.7.10.4), and I’ve run into a limitation that I’m not sure how to properly handle....
UCM 6202 Configuration with CISCO 7821-K9
Dear All, We are trying to configure CISCO 7821-K9 with UCM 6202 Configuration, but the IP Phone is showing "Registration in Progress with buffering Symbol" Request everyone to guide and support us
ASA 5525 Firewall failover setup.
We have two Cisco ASA 5525 firewall at Block A and Block B where the failover was not setup yet. Should i need to configure one port at firewall and install new physical fiber cable with transceiver for peer to peer connection?
Management access from directly connected Anyconnect client 9.18+
Hi,I have an FTD2140 running ASA and use management0/0 for SSH and HTTP management access to the firewall whether on-prem or remote. On the 9.12 train, we can manage the same firewall we are landing on with "management-access management". After upg...
Isolate VLAN X from other VLANS
Hello Together,we have a Catalyst 9500 Core Switch and I wan to Isolate a specified VLAN (VLAN 5) deny to connect to all other VLAN. Here is a simple configuration and explanation what the result should be.VLAN 2 (Server) 10.1.2.0/24 Gateway VLAN int...
Cisco CLI Analyzer 3.7.2 on win11 won't start after upgrade.
I just upgraded to 3.7.2 and now it wont launch. I acts like it is going to start and task manager show 6 or 7 instances of it when I launch it. But no window ever opens up. I have tried uninstalling and reinstalling that did not help, and Get no e...
MDS 9000 Series Affected by Microsoft KB ID: 5062710
I'd like to check if the MDS9000 series is affected by the following article (Microsoft KB ID: 5062710).https://support.microsoft.com/ja-jp/topic/windows-%E3%82%BB%E3%82%AD%E3%83%A5%E3%82%A2-%E3%83%96%E3%83%BC%E3%83%88%E8%A8%BC%E6%98%8E%E6%9B%B8%E3%8...
| User | Helpful Count |
|---|---|
| 85 | |
| 49 | |
| 44 | |
| 44 | |
| 37 |
