Activity in Technology and Support
Resolved! Super User Admin in CX Cloud - Where to start?
I'm new to CX Cloud and I've been designated as the Super User Admin. Where should I start?Thanks,Charlotte
wifi network drops during the day - AIR-AP2802I-Z-K9
Deal All, I would like your help regarding a problem that has been going on for a long time. Many users at the company have complained that the WiFi connection on their laptop drops several times during the day. I have been monitoring some of t...
Resolved! FDM DHCP Relay
HelloWe have Cisco 1140 with FDM Management, version is 7.2.5. How do I need to configure DHCP Relay? Because I did all configuration, but int not working
Hello,Can anyone explain for me why my PC4 and PC5 cannot get DHCP IP?
My PC0 to PC3 can get IP from DHCP service, but I don't understand why the same thing cannot happen on PC4 and PC5. Please explain for me, thank you!
Trustsec Network Authorization not Working
Hi All,I am newly building trustsec in my environment,trying to add one of the switch under trustsec. Have configured Trustsec settings and COA on the ISE for the switch and added the appropriate aaa commands , radius servers and cts commands.But sti...
CUCM Trace Logs Limited to the Previous 10 Minutes Worth of Calls
This is a 2-server cluster of CUCM 12.5It is a small deployment of around 100 phones that don't handle a large volume of calls.I'm pulling logs for the CallManager service.Typically I would expect to be able to go back at least weeks but I can't pull...
Mitel - DHCP Discovery
Hi, I have a Mitel 5312 phone plugged into a switchport configured for ISE but when it boots up it gets stuck on DHCP Discovery. If I put the port to authentication open then it goes through and boots up as normal.The logs all look ok but I can't see...
Hide Finesse Gadget Header/title
Hi, I'm trying to hide the "Supervisor Assist Gadget" title for the Finesse 3rd party gadget. In the gadget xml, I removed the title by which I was able to hide the gadget title and the text moved up to where the title is but now I'm getting empty s...
MACSec not supported on N7K-F312FQ-25?
Hi All,Can any one confirm that on a N7K-F312FQ-25 SUB2E is IEEE 802.1AE MACsec not supported?thanks with any pointers.with kind regardspiotr
AP9115axi
Hi ,I am facing one issue. AP9115AXI (access point) acquired IP address from DHCP. Confirmed with ARP table on switch.But the command sh cdp nei detail - doesn't show IP address of AP. AP not yet associated to WLC.Any suggestion?With Regards,Ravindr...
Help with dynamic routing
Why I cant send packet to same vlan on the different router ?
Not powering up KEM (PID: CP-8800-A-KEM)with CP 8851
I bought a new KEM (PID: CP-8800-A-KEM) along with the cisco ip phone CP8851 but unable to power up the KEM. I am using C2951 ISR with IOS 15.6 and Cisco Unified Communications Manager Express (CME) version 11.5. Please note i am using call manager e...
Resolved! C2960L-SM - ssh connection not possible
Hi, I have a C2960L-SM and noticed that I can't connect over ssh anymore. I getssh_exchange_identification: Connection closed by remote host If I run show ip ssh it seems ssh is running:SSH Enabled - version 1.99 ... and so on What can I do? Especial...
SSM ON-Prem TACACS+ and Clearpass
Hi,I am trying to configure TACACS+ on our SSM On-Prem server so that I am able to login on the Webinterface with my AD user. The TACACS+ configuration is done in Clearpass. And the test in the configuration window on the SSM server was successful.Bu...
Configuring Type 6 Passwords in IOS XE
HistoryRequirementsConfiguration StepsManaging the KeysChanging the PasswordVerificationThese need to be reviewed \ changed.These are safe to use.FAQReferences History Traditionally Cisco has used several different methods for storing passwords and ...
| User | Helpful Count |
|---|---|
| 102 | |
| 101 | |
| 83 | |
| 75 | |
| 58 |
