Activity in Technology and Support
LAN automation keeps faling due to certificate install error
Hello, I use to run LAN automation on my lab without any issue. I am not sure if that is related but few months back, in order to replay a customer case, ran some tests by changing the certificate using a certificate chain. Since a few days I was tr...
ASAv can upgrade esxi version after done install
Hi All , After done install and configure ASAv . If I want to upgrade Esxi Version from 6.0 to Version 7.0 Can I do that , Now ASAv Version 9.16 . I try to check ASAv can support Esxi 7.0 but I'm not sure about process upgrade esxi software . What wo...
Resolved! Cisco CUCM Hyper-V
Can cisco CUCM running under Hyper-V?
Reimage Cisco FTD 1120 - empty disk, missing correct FXOS
HelloBeen struggling with a Cisco 1120 today, no warranty left, but would like to get it running again. Tried a new disk and flashed it with tftp from rommon, also tried USB. Unit comes up with FXOS, but not able to install FTD with scope --> firmwar...
Web GUI Access Issue After Switch Restart
Dear Cisco Support Team,I would like to report an issue we are experiencing with one of our Cisco switches CBS220 .After restarting the switch, we are able to access the Web GUI normally for a short period. However, after some time, the Web interface...
Clarification on DELETE behavior in Duo Automatic Provisioning.
In Duo Automated Provisioning using SCIM, I’m observing the following behaviour and would like to confirm if this is expected:When a user is first removed from a SCIM-provisioned group and then deleted from Duo, no outbound SCIM DELETE request is sen...
ISR 1121-4P Cable Console Access
Hello,I recently got an ISR 1121-4P and there is a MICRO-USB Console Port in it and I can't get an active console connection.I've already installed the USBtoSerial Console Driver on my device. The router is completely new and I also tried to factory ...
Cisco ISE HA License Query
We are currently using two ISE nodes in our infrastructure as standalone. Now we want to configure them in HA. Do we need a separate license, or is one license enough for HA?
Resolved! DUO - allow logon locally
Hi, We are using DUO Wondows logon 3.1.1 to enable MFA for our Jump servers. Is it necessary that, users who need to authenticate to those Jump servers should be under the GPO policy “Allow logon locally”. we have around 500 users who need access to ...
SYS-4-CHUNKSIBLINGSEXCEED
Hello everyone,Here is my problem :%SYS-4-CHUNKSIBLINGSEXCEED: Number of siblings in a chunk has gone above the threshold. Threshold:10000 Sibling-Count:45558 Chunk:0x20EB71D0 Name:Elsinore TSIP P -Process= "GNSS Periodic Process", ipl= 0, pid= 92Ver...
Nexus Dashboard on Proxmox
Anyone know if it’s possible to deploy the Nexus Dashboard software on proxmox? I tried for a while using their qcow2 and couldn’t quite get it to boot.As everyone moves away from VMware Cisco will need to address this.Thanks all
Port-channel between FTD and ASR 920
We are having issues establishing a port-channel between an FTD 3110 and ASR 920. FTD LACP mode is set to "Active" while the ASR is set to "Passive". But it doesn't work.However, we have seen the FTD 4110 with an LACP mode of "On" and ASR "Passive" w...
NDI for telemetry vs ACI Multi-Pod (inside a Multi-Site) configuration
I have the scenario where two L3Out in eBGP per each POD of a multi-pod scenario for NDI vs FABRICs communication for telemetry, is configured.We applied the flag "advertise host routes" at the "inb" Bridge domain but what we see on L3Out towards ext...
CSCwr00047 - Mobility tunnel between 9800-40 WLC and AireOS
Mobility tunnel between 9800-40 WLC and AireOS WLC flapping, after upgrade of 9800-40 WLC to 17.12.6aHello,Will this be resolved in the next version 17.12.7? We can't just go with a workaround.Thank youPeter
Cisco EEM scripts
Hi Experts,Need your help one more time I am configuring EEM script for switches backup but i facing below errorsConfigured command - action 25.0 cli command "copy running-config ftp://CISCOSWITCH:Passwd@192.168.10.10/SWITCH/IN/$h/$h-$t abc.txt"Error...
| User | Helpful Count |
|---|---|
| 108 | |
| 76 | |
| 53 | |
| 51 | |
| 30 |
