Technology and Support

Meet and connect with other members who use Cisco Technology
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Browse the Community

Cisco Software

Cisco Software training materials and resources for Enterprise Agreements, Smart licensing and Smart...

4721 Posts

Cisco Start

Engage with your peers and Cisco about enterprise-class technology tailored to small and medium-size...

231 Posts

Collaboration

Engage with your peers and Cisco about collaboration products such as contact center, IP telephony, ...

216908 Posts

DevNet

Connect with other Cisco technology experts on topics of automation and programmability of Cisco pla...

28108 Posts

Data Center and Cloud

Professionals using or considering Cisco data center technologies can join the conversation to discu...

43653 Posts

Internet of Things (IoT)

Collaborate with your peers and Cisco on all areas of IoT to discuss what happens when the internet ...

247 Posts

Networking

Collaborate with peers and Cisco on all aspects of your network, including Cisco Digital Network Arc...

290957 Posts

Online Tools and Resources

Find tools and resources to streamline your service and parts logistics questions, technical documen...

8373 Posts

Security

Explore the security forums and share your expertise about firewalls, email and web security, Identi...

202695 Posts

Service Providers

Explore information and join discussions with peers and Cisco about Next-Generation Internet, MPLS, ...

17359 Posts

Services

Interact with peers and Cisco about Cisco Services including design, analytics, CSR and ServiceGrid,...

5676 Posts

Wireless - Mobility

Connect with peers and Cisco on all aspects of wireless tech including security and network manageme...

58375 Posts

Activity in Technology and Support

Cisco ISR

Any Australians here using enterprise routers as their edge device connected straight to their NBN NTD? I have a Cisco ISR4451-X-AX-SEC/K9 IPBASE I'm wanting to try this with (don't ask why, there is no why haha)Looking for any advice or config const...

multicast VRF through global routing table

hi team,I have c9300 connected to SRX 340 via static route. I have also VRF on this switch with vrf default route through global. the VRF has  source multicast and needs to get out through global routing table.  VRF config po11no switchportip vrf for...

Cisco C1000FE-24T-4G-L, C1000FE-48T-4G-L cannot connect

There are these two switches.1. When connected using the downlink port, the link comes up normally.ex) c1000fe24T(fa1/0/1) ↔ C1000fe48T (fa1/0/1)2. However, if you connect using an uplink port, the link does not come up.ex) c1000fe24T(gi1/0/1) ↔ C100...

Translator by Community Manager
  • 427 Views
  • 4 replies
  • 0 Helpful votes

Catalyst Center VA 2.3.7.4 install failing

Trying to install Catalyst Center Virtual Appliance ver 2.3.7.4 to an ESXi 7 host.  After the VM is created, I can go through the install and configuration steps without issue.  However, after logging into the GUI, I'm greeted with a blank home scree...

Theo W by Community Member
  • 93 Views
  • 1 replies
  • 0 Helpful votes

MacOs BYOD

Hi,  not much familiar with MacOS, any advice on MacOS provisioning for BYOD ?  its running Tahoe 26.0.1, I did posture update and the OS is supported, using CiscoTemportalAgentOSX 5.1.13.86 and MacOsXSPWizard 3.4.0.0 for result. it gets redirected, ...

ammahend by VIP Alumni
  • 77 Views
  • 0 replies
  • 0 Helpful votes

QoS Scheduling before or after IPSec enryption

Hello,I am a little confused about the following statement on the document Security and VPN Configuration Guide, Cisco IOS XE 17.x - IPsec Anti-Replay Window Expanding and Disabling [Cisco IOS XE 17] - Cisco"Moving QoS scheduling before the encryptio...

JUANNN by Spotlight
  • 86 Views
  • 0 replies
  • 0 Helpful votes

IOS XE EVPN IRB multihoming failover traffic loss

set up a IRB anycast gateway in two PEs for multihoming for one CE according to below guide. https://www.cisco.com/c/en/us/td/docs/routers/ios/config/17-x/mpls/b-mpls/m-evpn-over-mpls.html somehow it worked as expected until one PE failed and the CE ...

daniel ng by Level 1
  • 168 Views
  • 3 replies
  • 0 Helpful votes

DUMP from remote equipment

Hello everyone how to take dump from remote equipment.link just for older cisco router for-example 1900 etc, i have router asr1001 eps doesn't workinghttps://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/ios-embedded-packet-capture/116045-pro...

Mlex1 by Spotlight
  • 257 Views
  • 5 replies
  • 0 Helpful votes

Resolved! Finesse om_calltype

We're creating a Finesse gadget that will do the work of a Workflow due to Workflows limitations of being only able to send five variables. With the gadget, we're able to send the variables that we want. One thing I noticed in the Finesse logs within...

Capture.JPG
Omar Deen by Spotlight
  • 225 Views
  • 2 replies
  • 0 Helpful votes

Resolved! IW-6300H-AC-I-K9 with two antenna

   Dears,            We have IW-6300H-AC-I-K9 AP, and we need to connect two antenna AIR-ANT2588P3M-N= to it And I need to know the possibility of doing this: Please note that according to the link https://www.cisco.com/c/en/us/td/docs/wireless/outdo...

most_ahdy by Level 1
  • 335 Views
  • 10 replies
  • 0 Helpful votes

Termination failed - Cisco Modeling Labs

Hi,I am not able to terminate this lab: Cisco Modeling Labs-20251025T19180562Have tried different suggested solution on this forum but nothing has helped. The lab has been in "Terminating" state for a week or so.Any ideas on how to solve this?

babalut by Community Member
  • 161 Views
  • 1 replies
  • 0 Helpful votes
Share your Expertise

Level up by answering questions in your area of expertise.