Activity in Technology and Support
Resolved! Temporary License for Virtual Secure Management Center
Here's the situation I'm in: My customer has a virtual FMC that manages the SFR modules in three ASA-5516s. That runs version 7.0 as we have found anything newer doesn't work.We are in the process of migrating off of the ASAs and onto three 1140s. I ...
Cisco asa 5545XseriesHi,
Hi can someone help me with the configuration of ASA 5545Xseries? I have the router to the 0/0 and one pc on 0/1.I want to use dhcp to have internet access.Can you please give me a complete example cause the previous asa i had were using different co...
SG350X-48MP no PoE with latest FW --- SG350X-24P PoE working
Hi to allI have two SG350X switches, a 48MP and 24P and wanted to upgrade them to the same and latest firmware.Unfortunately the 48MP delivers PoE only up to FW 2.5.5.47. I tried certain versions like 2.5.7.85 and also the latest image_tesla_hybrid_2...
DHCP on Catalyst-1300 is it possible?
I'm trying to setup a new Cisco Catalyst 1300 with have a DHCP, but I'm getting told by chatgpt that it can not handout ip address, since it can only do DHCP Relay/Forwarder, DHCP snooping since it has limited layer 3 capabilities. Is that the case?
9200 upgrade fail because ssh got disconnected
Today I was upgrading remotely a 9300 IOS XE but suddenly while I was waiting after the command: install add file flags:file active commit There it was a disconnection for 1 minute with the ssh session and the Switch didn’t display the wizard again. ...
vBond IP Addressing in Hybrid SD-WAN Deployment with MPLS and Internet
Hi everyone,I’m working on a hybrid SD-WAN solution where all controllers are deployed on-prem, behind a firewall.I have two types of connectivity available MPLS and Internet. During the device onboarding process:Devices using MPLS will have the vBo...
automatic generating syslogs logs
hello all, i would like to ask you for advice. i would need to send from my devices each hour a syslog message (for example heartbeat_nameofdevice) each hour to Qradar. those devices are nexus 9K (9.3.9) and ASA firewall. i tried to configure it with...
Adding int to Mgmt-vrf
Hi,N00b question, please be gentle!Swapping out a SG to a Catalyst switch (C9300) at home, and very much not familiar with IOS!I've configured a Mgmt-vrf, which includes interface 0/0 (the physical RJ45) and applied VLAN 1 / 10.0.1.5/24 to itHowever,...
Cisco UCS C240 BE M4 S2 | UCS-ML-1X324RU-G
Hello Freinds Pls Advise on the below RAM 32 DDR4 for Cisco UCS C240 BE M4 S2 if it's okay for this box UCS-ML-1X324RU-G - Cisco 1x 32GB DDR4-2133 LRDIMM PC4-17000P-L Quad Rank x4 Replacementthanks a lot
unable to add vrf into a interface
Hi Team, vrf already created, however I am not able to add a interface in a specific VRF. Model: C1101-4P Getting below error: router(config-if)#vrf ?% Unrecognized commandrouter(config-if)#ip vrf ?% Unrecognized commandrouter(config-if)#ip vrf...
Resolved! HSRP over L3 Po
Dear People:) I am about to finish my education and regarding that we are preparing a little setup. This consists of 2 FW with a VIP and an internal network of 2 OSPF zones and 1 in DMZ, connected to 2 pcs of L3 switch. We have to use OSPFv2 down...
cisco IOS XE Upgrade
Hello , we are using Cisco Catalyst 9300 as below in install mode and we have completely classical routing features etc. As we want to upgrade on Cisco Portal we have no more IOS Image with same Bengaluru series. I believe now we have option to...
NSO not using commit-confirmed to configure a juniper via netconf NED
Cisco NSO use netconf NED to manage some juniper routers."show devices device xxx capability" from NSO returns below line, indicating the router is a commit-confirmed capable router."capability urn:ietf:params:xml:ns:netconf:capability:confirmed-comm...
Strange behaviour of ACL with Object Group
Very strange behaviour on a layer 3 switch. The second entry can affect the first entry in an ACL.A computer is in a vlan. The vlan has an ACL. The ACL references an object group to specify the protocol and port number.interface vlan4 ip address 192....
SD-wan Route leaking questions
Hello guys! I got confused with route leaking between the vpn0 and a service vpn (105 for instance). I have more than 1 default route in the vpn0 (all are static) and would like (according to the live https://www.ciscolive.com/c/dam/r/ciscolive/globa...
| User | Helpful Count |
|---|---|
| 185 | |
| 118 | |
| 92 | |
| 84 | |
| 76 |
