Technology and Support

Meet and connect with other members who use Cisco Technology
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Browse the Community

Cisco Software

Cisco Software training materials and resources for Enterprise Agreements, Smart licensing and Smart...

4603 Posts

Cisco Start

Engage with your peers and Cisco about enterprise-class technology tailored to small and medium-size...

223 Posts

Collaboration

Engage with your peers and Cisco about collaboration products such as contact center, IP telephony, ...

216515 Posts

DevNet

Connect with other Cisco technology experts on topics of automation and programmability of Cisco pla...

27912 Posts

Data Center and Cloud

Professionals using or considering Cisco data center technologies can join the conversation to discu...

43341 Posts

Internet of Things (IoT)

Collaborate with your peers and Cisco on all areas of IoT to discuss what happens when the internet ...

243 Posts

Networking

Collaborate with peers and Cisco on all aspects of your network, including Cisco Digital Network Arc...

289950 Posts

Online Tools and Resources

Find tools and resources to streamline your service and parts logistics questions, technical documen...

8231 Posts

Security

Explore the security forums and share your expertise about firewalls, email and web security, Identi...

201708 Posts

Service Providers

Explore information and join discussions with peers and Cisco about Next-Generation Internet, MPLS, ...

17257 Posts

Services

Interact with peers and Cisco about Cisco Services including design, analytics, CSR and ServiceGrid,...

5633 Posts

Wireless - Mobility

Connect with peers and Cisco on all aspects of wireless tech including security and network manageme...

58074 Posts

Activity in Technology and Support

Redundant WAN Design – Asymmetric Routing Issue

Hello Expert,I'm working on a somewhat complex network design and could use your expertise. I have two sites, each with a similar setup: a firewall and a Layer 3 switch.At Site 1, the firewall is deployed in a "router-on-a-stick" configuration with t...

duahimanshu816_0-1751671746624.png

ISE Upgrade 3.0 to 3.4

Hi All, Just wanted to ask of direct upgrade ISE 3.0 to 3.4 is now supported and possible? I've run URT and able to get success but I am not sure if direct upgrade is now fine.

mics by Community Member
  • 150 Views
  • 6 replies
  • 0 Helpful votes

Resolved! Taildrop avoidance for critical traffic

Hello Experts , I have a critical application traffic which passing though my Cisco ISR 4321 and i noticed that some packets being dropped as Taildrop , Please find below output from packet-trace debug :    sh platform packet-trace summary | i Gi0/0/...

qsosan20 by Level 1
  • 193 Views
  • 11 replies
  • 1 Helpful votes

Mac Devices failed to connect when AutoQoS is set to Fastlane

Hi,we are running SDA with Wireless. Today I enabled Fastlane checkmark under the SSID setup (Design > Network Settings > Wireless), which basically, does the following, as far as I know:1. changes the EDCA per band from wmm-default to fastlane, if n...

MUP0 by Level 1
  • 1197 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Problem with Web Browser and ACL

Hello guys I just made this simple topology with 3 router, 3 switch 3 pc on 1 switch, 3 on other, and last switch with a web server (internet) and a dns server. I also activated RIP between all the routers and ACL permit on the router connected to in...

OwlKun by Community Member
  • 179 Views
  • 8 replies
  • 0 Helpful votes

Implementing Group Encrypted Transport VPN (GETVPN)

                                                               Implementing Group Encrypted Transport VPN (GETVPN)                                            All router's are configured with ip addresses and configured ospf as routing protocol and...

Blue_Bird_0-1751714941349.png Blue_Bird_1-1751717524603.png Blue_Bird_2-1751717549337.png Blue_Bird_0-1751721648324.png

NCS-57C3 MPLS small frame thoughput

We have a simple l2vpn xconnect between a new NCS-57C3 and an existing ASR-9906 via 100G link in a single rack.  We have JDSU 5800 test units attached to both ends on 10G ports.  We have a customer requesting that their RFC2544 test be able to pass 7...

pboehmer by Level 1
  • 452 Views
  • 3 replies
  • 0 Helpful votes

Issues with wi-fi whasher and dryer

I have an issue with my wi-fi washer and dryer. Just I can connect only the washer to wifi. The dryer has an error with connection. Do I need a extra wi-fi device to connect it?Thank you!

Resolved! not able to use UNII 3 channels for 9120AXE-E

hello experts ,we are using 9120AXE-E , the E regulatory domain which is for Europe and middle east.   in Qatar although the UNII 3 channels are allowed i am not able to select them in the 5 GHz profile.  the issue is we are facing DFS issues and we ...

N540X-6Z18G-SYS-A and BFD

Hello, I'm trying to configure BFD parameters under BGP, and while it allows me to configure timers I can't seem to find how to configure BFD fall-over on my peer. It does allow me to configure BFD fast-detect but I specifically need to enable fall-o...

sdunc by Level 1
  • 477 Views
  • 3 replies
  • 0 Helpful votes

Clients not connecting due to DHCP timeout

Hi, we have had an issue with a rollout of new AP's on site.  The AP model is 9120 and the WLC is 9800 17.9.5, Switch infrastructure is 9300L on 17.09.04aWe had rolled out 109 AP's across our site with no issues however the last 3 we have activated h...

Share your Expertise

Level up by answering questions in your area of expertise.