Activity in Technology and Support
Artificial Intelligence (AI) at the Edge
Artificial Intelligence (AI) at the Edge by Alexander Stevenson, Cisco DevNet IoT Artificial Intelligence (AI) is often used as an umbrella term to describe intelligent agents that take inputs from their environment and attempt to achieve a cognitiv...
Catalyst Center Get Device List in Workflows
Trying to figure out and understand how I can use the Catalyst Center Get Device List API within Workflows and extract all of the responses into a single variable or table please. The Get Device List API has a maximum output of 500 devices per API ca...
Resolved! Firepower 4125 - how to resolve plugin 157288,
Our current ACAS scans are showing plugin 157288, TLS Version 1.1 Deprecated Protocol findings on Firepower 4120 and Firepower 4125 with FTD devices.The Firepower 4120 is running version 7.2.9,The Firepower 4125 is running version 7.4.2.2I am asking ...
Resolved! Required image not found on AP downloading image from controller Loop!
I am trying to connect a replacement Cisco Air-Cap-1552E that I am trying to connect to our WLC5508. . It says required image not found on AP, downloading image from controller. It looks like the device is stuck in a downloading software and reboot...
Cisco ISE Rebuild Issue
So we had an ISE which fell over after I've rebuilt our ISE with base software image (3.1.518), ready for deploying it back onto the network with the other appliance in a HA pair. I've already raised this with Cisco TAC, but just wondering if someone...
Router is not using default gatway for ICMP Ping - strange behavior
I am simulating a simple network technology with IOU L3 images and observe a strange behavior with image version 17.15.1The network consists of 4 routers, One of them is named a "SourcePC" (bottom of diagram) - a router from which I do an ICMP ping (...
N9K-C9508 Standby SUP replacement
Nice to meet youHow do I replace an N9K-C9508 standby SUP running in ACI mode?I checked "Installing or Replacing a Supervisor Module" on Hardware Installation Guide, but it says "Perform physical maintenance to the supervisors of the Nexus 9500-serie...
Is the file viptela-bond-20.16.1-genericx86-64-qcow2 used for both?
I downloaded refplat_p-20250724-supplemental-iso.zip file from CML 2.9.0.from the zip file, I got refplat-20250718-supplemental.iso.and from the ISO file, there is a folder as this:G:\virl-base-images\cat-sdwan-vedge-20-16-1The file under the folder ...
Interface TenGigabitEthernet1/0/0, link down due to remote fault
Hello All, I observed Interface TenGigabitEthernet1/0/0, link down due to remote fault on ASR1006 and the link is down. May i know what is the exact issue ? Jul 21 04:04:06.871 EDT: %IOSXE_SPA-6-UPDOWN: Interface TenGigabitEthernet1/0/0, link down...
Link down due to local/remote fault
I'm curious what the difference is between the following log entries: %IOSXE_SPA-6-UPDOWN: Interface TenGigabitEthernet0/3/0, link down due to remote fault%IOSXE_SPA-6-UPDOWN: Interface TenGigabitEthernet0/3/0, link down due to local fault What would...
Secure Access Documentation
Hi all, Does anyone else get 404ed when they click on a link to documentation from within Secure Access? It tries to take me to this address (for example re: ZTNA Traffic Steering): https://securitydocs.cisco.com/api/v0/apps?appId=SecureAccess&topic=...
Resolved! Monitoring of ISE for certificate expiry
Hi there,Customer wants to receive a message from ISE (using syslog, SNMP, SMTP) when the ISE certificates are about to expire.Is there a built in syslog, SMTP or other notification method for this?regardsHenk
API access to cdFMC audit log configuration changes
My developer colleague and I (detection engineer) would like to call the following API endpoint:GET/api/fmc_platform/v1/domain/{domainUUID}/audit/configchangesHowever, according to the API documentation this call requires a parameter called sn...
New to network programing
I'm exploring network programming because I've got a project where it seems like it would be critical / necessary. I want to develop an automated way to backup the running config, diff it to the last stored copy, store / version if different, and mos...
TEAP for Windows 10 using Group Policy and ISE TEAP Configuration
With Windows 10 build 2004 and ISE 2.7 Patch 2 TEAP (EAP Chaining) is now supported. It seems currently TEAP can only be configured manually for non-domain joined workstations. This is due to the TEAP option not available under the group policy confi...
| User | Helpful Count |
|---|---|
| 69 | |
| 57 | |
| 51 | |
| 45 | |
| 42 |
