Activity in Technology and Support
SPA122 can't access web interface despite enabled remote access
I have an SPA122 with its WAN port connected to a fibre wi-fi router's LAN port. I configured the SPA122 using 192.168.15.1 with the LAN port connected directly to a PC. I have set a new admin username and password and enabled remote access. I can se...
mantagifts.com domain is not resolved by OpenDns
About 2 months ago we moved the server of mantagifts.com to a new ip address: 57.130.30.42This domain already exists for more than 10 years and is a stable B2B webshopHowever somehow OpenDns does NOT propagate the A record properly (all other authori...
Cisco CP-8851 IP phone
I have a Cisco CP-8851 IP phone that is stuck on the logo screen and does not progress. It is not receiving an IP address from the DHCP server. I tried resetting the phone, but the issue persists. When I use the reset sequence 369#, the microphone, s...
Vicon IP Cameras Issue in C9300-48uxm running IOS-XE 17.9.1
Hi All,We're facing issues in C9300-48UXM 8-Stack switches running IOS-XE 17.9.1. All our Vicon IP cameras are goes offline when the switches are suddenly rebooted due to maintenance. POE devices are online like Cisco IP phone, Cisco APs, PC, and oth...
Is stackwise virtual going to be supported with meraki?
I have just been doing some digging in to the meraki dashboard and catalyst 9k series and are wondering if anyone knows if the stackwise virtual with the 9500 series will be supported. I know that switch stacking is possible and supported with the 9...
Not getting Ip Address command on SFP interface on C8355-G2 router
Hi Community,I have added the SFP module "SFP-10G-SR-S" to my C8355-G2 router,however when i tried to setup the ip address on it it does not give me ip address command. I tried to make that port with layer using no switchport command but still no luc...
GA Announcement: Cisco Wireless Active Testing On-Prem
Announcing General Availability: Proactively Assure Your Wireless Experience with Cisco Wireless Active Testing On-Prem We are thrilled to announce the general availability of Cisco Wireless Active Testing with ThousandEyes! This powerful new solutio...
Incoming connections timeout or slow when do connect. isrc1111
i have had the system i have in place for some time and had no problems, when using a 2 router approach [isp1 and isp2] but since i merged both onto 1 device, ISRC111 there is an issue with incoming connections via isp1. i am using the same acl's and...
Catalyst 6500-E Series Chassis compatible line cards help
Hi all, I am trying to find a compatible 10GE Ethernet line card for 6504-E chassis. After checking EOL lists for replacements I found some newer cards. How can I be sure of compatibility of older chassis and newer line card? Old compatible card (EOL...
Port channel mode cannot be changed to ON for CCL links. Why?
firepower4145 /eth-uplink/fabric # enter port-channel 48firepower4145 /eth-uplink/fabric/port-channel # set port-channel-modeactive Activeon Onfirepower4145 /eth-uplink/fabric/port-channel # set port-channel-mode onfirepower4145 /eth-uplink/fabric/po...
Used All community Of route IN RIB and decide to action
Hi i have this pathAdvertised path-id 1Path type: external, path is valid, is best path, no labeled nexthop, in ribAS-Path: 208555 , path sourced external to AS172.18.14.238 (metric 0) from 185.217.6.34 (192.168.20.1)Origin incomplete, MED not set, l...
BGP Path Attribute MED
I learned that MED is applied to outbound updates , dictating the best inbound traffic into the AS, but I saw the vice-versa is also true like you can apply med for indbound updates also and it works the same right??
Post 3.4, Patch 4, replication stop with PAN and CLI failed to connect
Post 3.4, patch 4, Replication stop between PAN and PSNs, error, Jediss replication failed, CLI access issue-error failed to connect to the server. throwing an error in the debug log : Error, Failed to connect to server, could not connect to test-ise...
Implementing Live Audio Streaming in Cisco CVP
Exploring the feasibility of live audio streaming within Cisco CVP, this post outlines an approach using a custom VXML application connected to a transcoding proxy. The proxy converts MP3/AAC streams into G.711 or 8kHz WAV for VVB playback, while DTM...
Why is my Cisco switch not connecting to the network?
I have a Cisco switch that is not connecting to the network after a recent configuration change. All cables and ports seem fine. Has anyone experienced this issue and found a solution?
| User | Helpful Count |
|---|---|
| 60 | |
| 55 | |
| 46 | |
| 43 | |
| 36 |
| User | Count |
|---|---|
| 22 | |
| 20 | |
| 14 | |
| 12 | |
| 11 |
