Technology and Support

What abbreviation to use for Cisco Catalyst Center?

After upgrading DNA Center to Catalyst Center I have trouble finding a decent abbreviation to use for dns entries and so on(3-4 letters)...DNA Center was dnac which was simple and unique enoughCCC (cisco catalyst center) is out because its a shoe bra...

I'm going to Cisco Live 2024! What can I expect as a Cisco newbie?

Hi all,Thanks to some generosity from Cisco and from my university, I'm headed to Vegas for Cisco Live this year! I am very excited for the opportunity, but also a bit nervous considering my level of experience. I am only a freshman in college withou...

Sip trunk between cucm with cucm and cucm with asterisk

I have a trunk between cucm 6.1.5 and asterisk but when a call is made from cucm to asterisk it disconnects immediately it is picked (call from asterisk to cucm is ok). But it is working with cucm 10.5. I try route call from cucm 6.1.5 to 10.5 then c...

Trouble with ASAv anyconnect radius login

Hi EveryoneI'm using a trial version of ASAv and i believe it has full functionality but is limited in 100kbps. I'm trying to set up remote access anyconnect vpn which authenticates to our NPS radius server. As you can see in the radius debug, it see...

Unable to ping between two tunnel points

Hello, I built using the packet tracer a simple topology of three routers with ospf routing. I created a tunnel between the two routers that are not physically connected to each other, but I can't ping between one end and the other. I managed to ping...

Resolved! C220M - SNS-3595-K9 invalid signature detected

Hi,Our old ISE C220M - SNS-3595-K9 is migreted to new one and I am trying to use it for labb by installning ESXI on the old ISE. But everytime i am trying to boot by usb, I got a messege "invalid signature detected - check secure policy boot in Setti...

ISE 3.2 Repeat Count Details

Hi,on ISE 2.4 in the live logs pages the report that one got clicking on the repeat counter was very useful because the endpoints were sorted by repeat counters. So it was very easy to find the endpoints with high repeated counters.With ISE 3.2 the r...

asr1002-hx - Licence question

Hi all,I am thinking of purchasing asr1002-hx and would like to make sure my understanding is right.I need crypto, vrf's,dmvpn, mpls, ospf, bgp.. full feature set..What I understand that I need is following :ASR1002HX-IPSECHW= Cisco ASR1002-HX Crypto...

One of the stacked switch goes to enable mode without password (9200L)

Hi,I have a problem with stacking two cisco 9200L's, after stacking, one of the pair goes straight to privileged exec mode, without enable password, while the other needs password for it. It's not the first time, this occurs, do you have any idea whe...

Duo Two-Factor Authentication for Palo Alto Admin UI without AD

Hello, has anyone successfully integrated Palo Alto Admin UI with Cisco Duo for 2FA without relying on Active Directory, but instead using a local user created on Duo solely for testing/PoC purposes? Any assistance would be greatly appreciated!

Resolved! Webex Room Kit Mini w/TelePresence Touch not getting IP address

Main issue: The Webex Room Kit Mini is pulling an IP address, but the TelePresence Touch unit, which is connected to the Room Kit's dedicated Touch port (which I assume acts at least as a pass-through network port) is not (it's getting a 169.254.x.x...

Resolved! GNS3 - IOSvL2 crashing on boot

I get the following error message: https://pastebin.com/WEwAvbsCThe network is shown in the image. I literally just press start all devices, connect to console and get that. I tried googling the error but nothing shows up.

Cisco FPR version 7.2.5 is possible make group lock for local user

Hello , Cisco FPR version 7.2.5 is possible make group lock for local user that connect to local network over AnyConnect. I want to make Anyconnect access in our network where we have more group policy, we can not find that we can lock local user fo...

Resolved! mac flapping

Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1/1/2Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1...

How to combine White List Entry - Server AND Mailadress

Hi all, i wonder if (and if yes how) its possible to combine a WhiteList Entry Server AND Mailadress. For example - we want to be sure that some mail adresses from a specific Server are whitelisted. Other Mails from this Server should be blocked and ...

Technology and Support

Browse the Community

Certified Remanufactured Equipment

Cisco Software

Cisco Start

Collaboration

DevNet Hub

Data Center and Cloud

Internet of Things (IoT)

Networking

Online Tools and Resources

Security

Service Providers

Services

Small Business Support Community

Wireless - Mobility