Activity in Technology and Support
Cisco ISE - hitting wrong NetworkDevice Group
Hello,For some reason, an authentication request for node 172.23.140.200 is hitting the wrong Network Devices Group, though there is a long prefix/32 available. Consequently, the wrong Policy-Set is chosen with Privilege Level1.Usually ISE is expecte...
CISCO MAB Auth for Wireless devices
Hi AllI want to configure MAB authentication for wireless users. The same SSID is used for 802.1X, and I would like to use MAB for specific users. Is that possible, and how can I achieve it?Thanks,
ISE - WIFI Profiling Issue
HI trying to do profiling using MAB over WIFI, i had created initial non-profile auth policy that has ACL from WLC (5508) that allows only DHCP, DNS and IP to ISE PSN, device are hitting this auth profile but keep in unknown state if i hange auth pro...
Overlapping network multicast routing
I have multiple overlapping radio man nets, which require to be in the 10.0.0.0/8. is it possible to route multicast traffic to and from each site with overlapping networks?
Resolved! Need Switch Stacking Help
HelloWe recently purchased 4 Cisco Catalyst 9300x 48x UPOE+ switches to use in a switch stack configuration. I have made sure that the Stack Wise cables are all connected properly but when the switches boot up only 3 switches are found and are in the...
redirect or forwarding to mobile not working if call received external
if a call received to pilot number it will play prompt at unity connection . if the caller accept option to ring at reception it ring there and if no answer it should forward to mobile number. what happens is that it get forwarded and call get receiv...
Resolved! Downtime for certificate renewal - ISE 3.2
We have an ISE 3.2 distributed deployment (2x admin, 2x MnT, 4x PSN). We're using a multiuse certificate for Admin, EAP Authentication, RADIUS DTLS, and Portal usages. We have multiple wireless controllers that each have the four PSNs specified (9800...
allow policy & A/D user
Hello,I created a new policy to block all generative AI except a couple sites that I allow.In the policy, I allow by identities and add active directory users so they can visit the sites. One of these users tested it and was able to reach the site no...
VLAN issues
I recently replaced the core switch at one of my sites that consisted of two separate C9300-48Ts and three other off brand switches and installed a new stack with a C9300X-48HX, C9300-24S and a C9300-48T (running 17.12.5). This is a layer 2 network c...
Resolved! CSCwo18785-"ERROR: The transceiver doesn't support this speed"200G-DAC
Facing the below issue and it is a blocker for our product supportability with Cisco 9000 series switches.CSCwo18785 "ERROR: The transceiver doesn't support this speed" while configure 200G on QSFP-200G-DACQuestions1) What is the current status and...
OSPF between Nexus Switches (in vPC) and Catalust 6800s in VSS
I am planning to connect a Nexus 3K pair in vPC with a Catalyst 6800 pair in VSS mode. Should I configure OSPF over vPC link? What should be the best configuration for this setup?.
Fail to generate configuration xml:expecting non-null value for field
Hi,I encounter an error when trying to display config preview on vmanage after making a some changes to a device value. Furthermore, this error only happen to vEdge(ViptelaOS) router and not on cEdge router. The error is "Fail to generate configurat...
Which One Becomes the DP and Blocking Port in This Example?
Folks, I am having a hard time trying to figure out why the G0/2 interface on CD1 switch becomes a blocking port, and the F0/21 becomes the DP. Thus making the F0/21the the blocking port on Acc4 switch. In this example, Acc3 is the root bridge, so al...
Back Reflection
We recently purchased and built out a DWDM mux solution that includes NCS 1001 amplifiers. The amplifiers are connected via an 11km dark fiber span. We have been running on it for about 3 months without any issues. Since we did not have any experienc...
How can I dis associate Controlled Devices
I came across this and think it's wrongCSFBEANF should be the only controlled device for this userHow can I remove the three that shouldn't be associated with beanf?
| User | Helpful Count |
|---|---|
| 102 | |
| 92 | |
| 90 | |
| 77 | |
| 63 |
