Activity in Technology and Support
Resolved! Posture Policy for Wired & Wireless endpoints
Hi All,I would like to know if it’s possible to create different posture policies for wired and wireless endpoints. For example, since wireless users typically use laptops and are roaming clients, the Cisco Umbrella service must be checked. However, ...
Stopping Brute force VPN attempts from devastating our NPS server
HI We have an ASA 5525 firewall and it's currently being attacked by brute force VPN attempts. This is affecting our NPS and causing it to crash. The outside interface has a simple deny any any rule which is blocking everything however the firewall s...
AIR-CAP1702I-Z-K9 Looping
Minha AP esta em looping sempre que coloco a versão lightyear
Cisco Anyconnect Microsoft MFA issue
Hello,We have the following issue. Two-factor authentication (2FA) via Microsoft Authenticator is configured on a Cisco ASA. The tunnel group on the ASA is connected to Cisco ISE, which acts as a RADIUS proxy.In the condition, the Cisco ASA's IP addr...
SFDataCorrelator down on Standby FMC
I have an HA pair of FMC's running v7.6.1.My Standby device is showing an alert "Process Status - the data correlator process exited x time(s)", additionally the Health Monitor is showing "SFDataCorrelator Down" and running pmtool status | egrep -i '...
Unable to Install IPERF3 via App-Hosting - Mandatory Layer Missing
Hi,I have been struggling all day in an attempt to get mlabbe/iperf3 installed on a 9300 running 17.3.5 using advantage.So far, I have tried saving the image using docker save which defaults to the "oci-archive" format (uses blobs) as well as using p...
Room Bar Pro + Navigator + Ethernet Microphones
Hello everyone,I face following problem, maybe some ideas to help?I have Room Bar Pro + Navigator + to external Ethernet Microphones (CS-MIC-ARRAY-T) connected directly to the Room Bar Pro. System was installed few month ago, and worked correctly, bu...
Inconsistent BPDU Forwarding Between vPC Peers After Switch Reboot
Hi all, I’m facing a strange behavior in a network topology with two pairs of Nexus C3548P-10GX switches connected in a fully meshed back-to-back vPC design. The root bridge is located in the first pair (note: peer-switch is not enabled). It seems th...
ASA to AWS IPSec tunnel - ASA is not initializing communication
I'm trying to initialize IPSec tunnel to AWS basing on AWS instructions and it looks that ASA is not even trying to initialize connection.When I turned on debugging, it looks that ASA is in receiver mode (I see connection attempts from old site), but...
ISE Expert Insight Series: Unlock the Full Potential of ISE
We are thrilled to invite you to an exclusive event that explores the cutting-edge advancements in Cisco Identity Services Engine (ISE). Gain actionable insights from Cisco experts on enhancing your network secuirty, streamlining upgrades and ado...
Configure Multiple Email Aliases in Cisco ECE with On-prem + Cloud
Dear All, Currently, we are running Cisco ECE 12.6.1 ES9 ET3 with on-prem email integration (Single Email Aliases). Now we are looking for the best practice and advice for the following requirement. We need to create another Email alias; the existing...
c8000v 17.15.3a in a Lab on KVM: vcode_pkt_PPE0 process CPU Hog
Hi, I setup an SDWAN Lab with several c8000v running IOS 17.15.3a running on QEMU 4.1.0 (EVE-NG Lab environment) with 4 vCPU and 8 GB of RAM for each c8000v. CLI on the c8000v was very slow. I have spotted a process called vcode_pkt_PPE0 that consume...
how to load the Configs to the 9300x switches using puty
Good morning, we have just received new 9300x switches and I need to copy the configs onto them using putty, however when I do this I get nothing but errors. could some one show me step by step how to apply the configs to the 9300x Switches. Thank y...
CSCwo48630 - Deployment is failing due to the policy changes report
We’re encountering the same issue on the newer 7.6 release with 12xx firewalls. Has anyone identified the root cause or received any insights from Cisco? Thanks in advance.
How can I get area A to talk to area B?
Hi there,I am using packet tracer and I have an issue with area A talking to area B or area B to area ACloud is configured to use modem4 to Ethernet6Server has DHCP on and can talk to router and other PC in area A but not area BArea A inside IP is: 1...
| User | Helpful Count |
|---|---|
| 81 | |
| 67 | |
| 60 | |
| 58 | |
| 57 |
