Activity in Technology and Support
EEM scripting help
I'm trying to have EEM script where I run the script manually and it display the output of the results in the session but for some reason I'm unable to do so. This is what I have so far(config)#event manager applet TestCommand(config-applet)# event n...
ASA5516 Recommended software version
I am configuring ASA5516 from scratch and trying to find out the current recommended versions.Could you please advise?Curretly:ASA Software Version: 9.8(2)Firepower Extensible Operating System Version: 2.2(2.52)Device Manager Version: 7.9(2)152
Using device templates to standardize configurations
Hi I'm running NSO 6.1.7.1 with juniper-junos-nc-4.12 NED.I'm trying to use NSO device templates to standardize certain parts of device configurations.In this particular case I'm trying to force a certain set of "apply-groups" on a given Junos config...
Resolved! Allocating DID's in CME
Dear All,I have both Cisco & Non-Cisco IP Phones which are reigistered in my voice gateway. Now i have got ISDN with DID's. How can i allocate some DN with DID number in order to call in both ways ( each extension 5000 calls outside, its DID should g...
C9800-80 in HA cannot install APSP6
Hello everyone,I'm trying to figure out a frustrating issue. Attempting an install of APSP6 keeps bombing out and I'm unsure what steps to take next. Software: Version 17.09.04aROM: 17.3(3r)Error in question: Dec 13 21:21:01 Eastern: %INSTALL-3-OPER...
3905 Line 2
Is it possible to make a 3905 have a second line?
High Memory Utilisation 9200L
We are seeing random high memory utilisation spikes on our Cisco 9200L switches, running version 17.9.4a. We thought this might be related to the application visibility that is pushed out to them via Cisco Catalyst Centre, so we disabled application ...
Reset mot de passe sur Cisco Nexus N3K(C-31108TC-V)
Hello, Je désire resetter le mot de passe d'un Switch Cisco Cisco N3K(C-31108TC-V). Je n'Ai pas accès au CLI via ssh ou console port. Merci pour vos retours
Cisco VPN Client cuase windows crashes
Hi,I have a newly reinstalled OS Windows 11 PC. There is Cisco AnyConnect Secure Mobility Client on my PC to connect to my work access. Randomly my pc crashes, basically freezes. After manually power off and power on When I check event viewer the las...
IE-3400 switch l2nat causing connectivity issues
Newly installing these Industrial switches for our PLC networks uplinked to C9200 switches. We are wanting to use some of the ports for l2nat and have gi1/1 as the uplink with the associated vlan (2009). L2nat works perfectly, but we would like to ...
redundancy in core layer
hi guys . i have a network with below topology. In the core layer, I want to have redundancy, which means that if the main core switch of my network has a problem, the backup switch will automatically enter the circuit. What method is there?
Cisco Jabber doesn't send PRACK
Hello Forum,Trying to understand the below.Call flow:Jabber -> CUCM -> CUBE -> ITSP.Invite to CUCM -> Invite to CUBE100 Trying to Jabber <- 100 Trying to CUCM from CUBE183 Progress -> CUBE and 183 Progress to CUCM-> At this point CUCM sends a PRACK t...
Loading config from file doesn't import MAC address table.
I'm using a 9200 device running IOS 17.9.I use a script and spreadsheet to generate my config file, which I then copy onto my devices via TFTP and then copy to the running config. Nothing unusual there. However, if I then ask the device to show me th...
Upgrading 1 access point in ME from 8.5 to 8.10.
I am trying to upgrade my 2801i in mobility express from 8.5 to 8.10. Note:- My main wlc is already in 8.10, I need to upgrade another access point so that it can join main ME WLC.
Rebuild Cisco ACI with a new version
Hi, we have a Cisco ACI in our LAB enviroment with an older version 2.2. We'd like reset/clean all the fabric (n.3 APIC,n.2 Leaf and n.2 Spine) and restart with a new version, the 5.2. Our hardware support it We don't need the backup of actual config...
| User | Helpful Count |
|---|---|
| 108 | |
| 81 | |
| 79 | |
| 66 | |
| 59 |
