Activity in Technology and Support
Cisco WLC upgrade
Hello! I have configured WLC with software version 8.8.130.0. To which version is it recommended to upgrade? Thank you!
Cisco ISE 3.2 OVA instable crashes
Hi Everyone,Cisco ISE 3.2 keeps crashing several days after the installation.The installation has been done successfully without any problems.After a couple of days the installation is malfunctioning.After several installations and change of the sel...
ise appliance migration from 35xx to 37xx
Hai All can any one please give best practices for below deployment customer has Cisco ISE 3515 running on 2.7 which is EOL/EOS we Proposed new 3715 model. For configuration migration suggestions.
Resolved! FTDv managed by FMC ntp issue
Hi,I'm using FTDv 7 managed by FMC v7. Logging issues are there and there is an error about FTD not synced.So, first step seems to solve the ntp issues. FMC GUI is there for ntp which I set and it seems to be ok, but I cannot find where is the ntp se...
FMCv 7.2.5.1: High CPU load - how to troubleshoot?
Hello everybody,our customer has a FMCv running sugg. rel. 7.2.5.1 and has a high CPU load of approx. 97%.(see attached screen dump).The VM has 4 CPUs, 32GB RAM and 250GB HDD.The FMC is managing a HA of two Firepower 1120 running rel. 7.2.5.A FMC reb...
Delete a decommissioned (and phys. removed) server - fails
I just wanted to clean up * decommissioned and * physically removed blade servers by * selecting one and pressing ["Delete"] at the bottom as usual from the inventory. But UCSM fails: "Operation is not permitted" Any Idea how to overcome this?
Resolved! File not found UCCX Custom File
Hi, we use a custom file in /opt/cisco/uccx/document/System that we can read and write from an uccx application with System.getProperty("uccx.customer.dir"). We use the in UCCX Editor the Document steps "Create FIle Document" to get a document variab...
1921 Router Config Help
Hello, I know very little about configuring cisco hardware and need some help..... we are currently running an 1800 router and I obtained a new to me 1921 router and would like to replace the 1800 router with the newer one, I managed to get it factor...
Configure Custom TACACS Role for Nexus 9K Using ISE 3.2
The Cisco Document Team has posted an article. This document describes how to configure a customized Nexus role for TACACS via CLI on NK9. Know of something that needs documenting? Share a new document request to doc-ic-feedbac...
Troubleshoot Attendant Console Issues in Webex Calling
The Cisco Document Team has posted an article. This document describes the most common issues faced with the Attendant Console tool in Webex Calling (WxC). Know of something that needs documenting? Share a new document request ...
Cisco Hyperflex cluster installation failed
Hi All, My hyperflex cluster failed with the error "configure Service profile(SP) failed" "Associating Service Profile" during the UCSM configuration in each server but validation was successful. I have 6 nos of hyperflex UCS 240 m5 all-flash nodes a...
IOS-XRv 9000 unreachable from non-local network
I have a IOS-XRv 9000 with SSH and gRPC enabled, running on the latest version of CML. gRPC is not working from a remote network?
crypto keyrings command not found
Router>Router>enRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#Router(config)#Router(config)#Router(config)#crypto key ?decrypt Decrypt a keypair.encrypt Encrypt a keypair.export Export keysgenerate Generate n...
Resolved! WSA
hello all, is it possible to access physical cisco WSA GUI without license ???
Repeating syslog Message and then Crash
We're seeing a continuous string of the following messages on a 9407 running 17.9.5. Eventually the switch crashes. I can't find any info on what these messages mean exactly and whether we're looking at a software or hardware fault. The supervisor...
| User | Helpful Count |
|---|---|
| 113 | |
| 111 | |
| 86 | |
| 64 | |
| 62 |
