Activity in Technology and Support
ise appliance migration from 35xx to 37xx
Hai All can any one please give best practices for below deployment customer has Cisco ISE 3515 running on 2.7 which is EOL/EOS we Proposed new 3715 model. For configuration migration suggestions.
802.1x Cert Auth - What does the PSN Do with the Client Cert?
Please see the attached file. When a Windows client connects to the network and its supplicant is configured to send the computer certificate, what exactly is the PSN doing with this certificate? In the attached i have a use of Lab_dot1x_Certs (See...
Unity: How To Trace Call Flow To A Mailbox or Handler
Hi,I am reading about Cisco Unity traces and may need a little help with this. The operator mailbox is receiving messages. I want to trace how a call is being routed to this mailbox. I know if a caller into Unity reaches the Opening Greeting and that...
CUCM 11.5 License bin file error upload
Hey. I got CUCM 11.5 License bin file. But cannot upload license to CUCM portal
FTD's - Firepower dropping HTTPS traffic using TLS 1.3 Hybridized Kybe
HelloWe have a lot of clients getting the following error when contacting diffrent sites: ERR_SSL_PROTOCOL_ERROR, we have read that SonicWall and Palo Alto also have these problemes. Solution is to turn off "TLS 1.3 Hybridized Kyber Support" in chro...
We want to utilise the 4 ports on the Cisco C9800-L-F-K9 to connect AP
We want to utilise the 4 ports on the Cisco C9800-L-F-K9 to connect APs - and SVI interface on the WLC have been created on trunk TenGigabitEthernet0/1/0 with wlan 5 and 100 and - access port vlan 5 on TwoGigabitEthernet0/0/0 should these two/4 ports...
SSM ON-Prem TACACS+ and Clearpass
Hi,I am trying to configure TACACS+ on our SSM On-Prem server so that I am able to login on the Webinterface with my AD user. The TACACS+ configuration is done in Clearpass. And the test in the configuration window on the SSM server was successful.Bu...
Duo Desktop not recognized
Hello, I am using Cisco Anyconnect to connect to VPN. The system is using Duo Desktop for device health. It is already installed, running and all the checks are ok. However, I am getting this error message and not able to proceed: Install Duo Desktop...
Resolved! Python script to deploy NAC commands
Hi All!I am currently deploying NAC in my organisation's switches and was wondering if there is a Python script to help ease this task.The commands are almost the same on all the ports, except for the dot1x/mab priority one when there's a device conn...
Cisco ISE cannot join Windows Server Core.
My Windows Server Core having an internal address of 192.168.50.2, when natting it (NAT) it has an address of 192.168.99.36 (I'm installing Windows Server Core image on an EVE-NG VM and the EVE-NG VM is installed on ESXi).I have a Cisco ISE VM instal...
WLC9800 map two vlans on the same ssid
Hello, I have a WLC9800 with 9115 APs.For clients, I have a Vlan (100) mapped to an ssid. I want to add another vlan (102) mapped to the same ssid.I have added the vlan 102 (configuration, layer2, add vlan), i have created a vlan group and added both...
NTP and Syslog packets with specific IP Address
Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...
Resolved! Restarting DRF Services
I just wanted to verify before I did it, that I can restart the DRF services on my CUCM 7.0 without disrupting anything but backups right? A job seems to be hanging and I can't configure anything because it says that a backup is in progress, even tho...
Resolved! Super User Admin in CX Cloud - Where to start?
I'm new to CX Cloud and I've been designated as the Super User Admin. Where should I start?Thanks,Charlotte
Resolved! Trunk commands for ISR ESM?
Hello,At my home, I had an 8 port 2960G switch die after a power outage today. I replaced it with a ISR 1921 that has an 8 port ESM. It's been a very long time since I messed with configuring ESMs... My plan was to just copy over all of the switch...
| User | Helpful Count |
|---|---|
| 111 | |
| 110 | |
| 87 | |
| 69 | |
| 62 |
