Activity in Technology and Support
Cisco WLC or Individual Management - At what point is WLC needed?
Right now, I am managing 4 access points(3702i), each part of their own network(each network reachable via routing). The networks are physically close to each other(in a rack). I was wondering if it's worth spending on a WLC(like the 2504) or just ma...
Cisco 2802i - Wireless Bridge to a Wireless Network
I recently wireless bridged a cisco 3702i access point to my home network via its GUI, running autonomous mode. It was very easy and worked very well, giving my computer internet access. This only required ONE cisco access point(the one I'm bridging ...
Resolved! Ikev2 tunnel-Need help with Configuration-
Hi Folks, I need Urgent help. I am trying to configure ikev2 tunnel between two CISCO Routers. However, the problem is that my router is behind a firewall and not able to properly route traffic to the other router. However, when i connect straight to...
Cisco ISE not support IOT device
Dear Cisco lover, We would like to seek your support on case not functional IoT device when we perform Closed Mode on cisco ise such the MAC addresss can't be learn on switch port. Once we configure on switch with Low Impact mode, the IoT device is ...
send Log ASA to Security Analytics and Logging for Secure Network
"I've configured syslog forwarding on my Cisco ASA to send logs to Secure Network Analytics, and the ASA's logging configuration is complete. However, I've noticed that the UDP TX counter for this destination is consistently at 3, which suggests logs...
Need Help with Cisco C240 M4SX RAID Controller and Fan Issues!
I recently got my hands on a Cisco C240 M4SX with 24 drive bays. It’s equipped with a Cisco 12G SAS Modular RAID Controller, but I’ve run into an issue I can’t seem to solve.From what I’ve read, using a non-Cisco PCIe adapter causes the system fans t...
Necessary Ports for Cisco 9800-CL
We are looking to implement a zero trust through ThreatLocker and therefore we would like to find out which ports on the WLC need to be able to communicate with our domain controllers, our radius server, and with the APs. I have already looked at the...
Update Firmware Cisco IP Phone CP-8851
Hi I want to update the firmware on my CP-8851but it doesn´t work as described in the different guides.acctually my main objective was to connect my CP-8851 through placetel, but as this didnt wanted to work so I asumed the former owner erased everyt...
Resolved! Config-Register question
I am running a 4506 Catalyst switch and CatOS. Here is the output of the show boot command.OFF_4506_24 (enable) show bootBOOT variable = bootflash:cat4000-k8.7-6-3.bin,1;CONFIG_FILE variable = bootflash:switch.cfgConfiguration register is 0x2ignore-c...
Cisco AIR AP 2800 Series - Stand Alone / Mobility Express mode
Hello Community,I have never worked with Cisco APs before and I have just come across two Cisco AIR-AP2802E-E-K9 access points.I would like to use them privately.The devices are currently running the Lightwight variant, as they were apparently previo...
Rearrange cisco 2960 WS-C2960X-48LPD-L stack of 8
I have a cisco stack of 8 switches connected at the moment.1 is the master as per show switch result *1 Master 0077.8d2a.8400 1 4 Ready2 Member 0077.8da8.1600 1 4 Ready3 Member 0077.8d2a.8b00 1 4 Ready4 Member 0077.8da8.1980 1 4 Ready5 Member 0077.8d...
Cisco ISE policy dic
Cisco ISE policy dictionary only to look up policy or is there better website or better to search?
Resolved! ISE installation stuck
I am trying to re-image 2.4 on an SNS-3515 by mounting ISO from a local machine. The image upgrade is getting stuck at the below stage. We have upgrade the CIMC and BIOS to the latest version. Verified the md5 too. Has anyone run into this issue ?...
Resolved! Cisco 2821 - Max PDVM2-64 modules that can be implemented
Hello.I've been reading the Datasheet for the Cisco 2821, and it says that the PDVM2-64 can be used on it. However, there are 3 PDVM slots available on the 2821. I was wondering if there is a limit as to how many of the PDVM2-64 can be put in the rou...
Cisco 4300 ISR4331/K9 Hardware Failure
Good Day,i have a Cisco 4300 ISR4331/K9 Hardware Failure. recently i saw that the ISC light is a solid amber lightRunning the show platform command, i see this0/4 PVDM4-32 booting 00:00:17: %SPA_OIR-3-RECOVERY_RELOAD: subslot 0/4: Attempting recovery...
| User | Helpful Count |
|---|---|
| 84 | |
| 64 | |
| 55 | |
| 53 | |
| 50 |
