Activity in Technology and Support
Dual WAN [Independent] on ISRC1111 connected to 3850 Switch; No Intrnt
Hello I had trtied to apply this scenario to my FPR1010 but either due to lack of understand or simply did not fit my needs, I decided the FPR1010 was a Firewall {obviously) and decided to let it be such and work on the ISRC1111. What I have posted b...
BIDI SFP
While install BIDI SFP on Cisco 9407 R and get optical power reading we faced below issueDiagnostic Monitoring is not implemented
Workflows API
Is there a Meraki/Workflows available to help manage our routine operations? For example, be able to bulk add/delete targets? I thought I recalled an API with the non-Meraki version of workflows, but I can’t find anything except one item in the early...
Resolved! PublicKey authentication on router, but Ansible still uses password
I have enabled only SSH publickey authentication on the router, and disabled password and keyboard authentication. But Ansible is still able to authenticate on the router using a password.IOS: 15.5Linux: Ubuntu Server 22.04From a Linux VM I am not ab...
dynamic vlan assignment -wpa2
Hi,I currently have three separate WPA2-PSK SSIDs, each mapped to a different VLAN.I want to consolidate them into a single SSID and use Cisco ISE to assign VLANs dynamically.Is it possible to perform dynamic VLAN assignment based on the client MAC a...
vNDO 4.1.1g get to the software image after dissociating from NTP for
Hello Freinds vNDO 4.1.1g get to the software image after dissociating from NTP for whatever reason, is there any methode to prevent it for NTP Check after the successful installation rescue-user@NDO-3:~$ acs health======Status======[critical] Node[...
NTP Config on WS3750-X
Hello FreindsAre there any things missed in the NTP server Below config? VMs has issue associating with this NTP ServerBelow NTP Config==============WS3750-X#sh run | sec ntpntp source Vlan64ntp master 5ntp server 172.16.100.254WS3750-X# 1 of the VM ...
airtime utilzation
From an airtime utilization perspective, I want to understand the impact of SSID design.Currently, I have:2 SSIDs configured as 5 GHz-only4 SSIDs configured as 2.4 GHz-onlyDoes this design reduce 5 GHz airtime utilization compared to having all SSIDs...
Cisco tri-radio AP dual 5GHz client roaming issue
I have an AP 9130ax, it has 3 radios: radio 0 is 2.4GHz, radio 1 is 5GHz and radio 2 is 5GHz. I'm seeing problems with clients connecting and disconnecting from the 5GHz radios. Where can I configure the roaming between these two 5GHz radios within t...
SG200-18 Firmware
Hi to everyone I am new here.I know that the SG200-18 has been EOL for a while, but I recently purchased one in good condition and I would like to update the firmware to the laste version.Does anyone have the files including the boot loader to upgrad...
Vlan deployment
I know it's a very silly question to ask, but I want to know whenever we create a vlan with vlan vlan-num e.g. vlan 10and then till we don't use exit and came back to configuration mode the vlan doesn't show up. Like why we have to explicitly 'exit' ...
BGP Path Attribute MED
I learned that MED is applied to outbound updates , dictating the best inbound traffic into the AS, but I saw the vice-versa is also true like you can apply med for indbound updates also and it works the same right??
Issue with cisco switch 3850, I set boot variable but it does not set
I have a Cisco switch c3850. I have recently updated its IOS. Now, I cannot set next variable boot so that the switch automatically boot from packages.conf in the next restart. I did set boot variable using this command "boot system flash:packages.co...
Call Drops After Few Seconds and One-Way Audio or No Audio in IP Phone
Dear Team,Facing two issues with our IP phones. Details are mentioned below:Issue 1: Call Drops After Few SecondsCalls are getting disconnected automatically after a few seconds of connection. This issue is happening frequently on both incoming and o...
How Get SPAN on VLAN 200 IN this Diagaram
Hi Dearsmost switches donnot support RSPAN IF port trunk on and port 2 is access vlan 200 Copy traffic SPAN on VLAN 200 ???
| User | Helpful Count |
|---|---|
| 59 | |
| 48 | |
| 46 | |
| 44 | |
| 34 |
| User | Count |
|---|---|
| 26 | |
| 18 | |
| 13 | |
| 12 | |
| 11 |
