Activity in Technology and Support
C1300X Fans
Are the fans on the C1300X switches thermally controlled?
Resolved! Download c1140-k9w7-tar.153-3.JB.tar ?
Hello all ! I'm searching where i can download this software "c1140-k9w7-tar.153-3.JB.tar" for my access-point. Can you give me a link where i can download it please ? Thank's
4G LTE Config on IR1101 - Commands not working
Hi I am using Telstra SIM card on Cisco IR1101, with slot 0/1/0. The current problem is all the profiles inactive, non public IP shown during show run. I called Telstra and they told the SIM is active and tested the internet connecting to phone Same ...
Cisco Packet Tracer Network Scanning
Not sure if this is the right place for this questions but... I work at a place that using the Cisco Packet Tracer software and have been for years until today. We have been banned from updating to the new PT version of 9.0.0 because our security/ ne...
CSCwo09244 - IOSlice temperature sensor shows as failed
The logs are uploaded and let us know the status.
Catalyst EVPN multihoming for non-fabric networks
Are there any configuration guides available for this feature for Catalyst 9300/9300x? We would like to configure and test for an upcoming design.
CCNA EXAM LAB QUESTIONS
Hi, I'll be sitting my CCNA exam in Feb of this year. Regarding the lab questions in the exam, do i have to type out the full command when in the CLI? eg: Could i just type "en" instead of "enable" or "conf t" instead of "configure terminal" ?? Any...
BPDU Guard
Just a simple question why it's recommended to use both Portfast and BPDU Guard together apart from the very fact that both should be used in access switches ports connecting to end users?? Like BPDU Guard will still work if I don't have portfast con...
Routing to SVI Over Trunk in IOS XE - Can reach hosts but not GW?
Good morning Cisco Community, I feel like i am over looking something simple here. I've built a SVI and propogated it into OSPF on a L3 device. On one interface of that device there is a host connected through two cascaded layer two acces switches....
Need assistance in fixing the uccx script
We have one script that was downloaded from the old UCCX 8.6 system and then uploaded to the new UCCX 15 system. When using this script, I am unable to answer calls from the Finesse desktop, although I can answer the calls from the phone. The other s...
Cisco 2802i AUX Port as LAN Port
Following the instruction from the link below, I converted the AUX port of one of our Cisco 2802i AP's to a LAN port. My hope was to feed a switch from it so I could provide network access to three devices. So far, I can not gain network access. Has ...
Can I ISSU upgrade a C9410R from 17.9.6 to 17.12.6 directly
I have a few C9410R chassis. I want to use issu to upgrade them from 17.9.6 to 17.12.6. If I use the install mode command to upgrade them, will both supervisors upgrade both the IOS and ROMMON statefully?
IE-9320-24T4X-E Port Configuration change
I have multiple setups with these network switches. At least on two different setups, we have connection issues with one of the ports (port #24). We verified that the port configuration has changed and the reminder of the ports configurations remain ...
Set an apply group via netconf on ios-xr
Running this netconf call via ncclient fails to apply the apply-groupdef main(): apply_group = """ <config> <interface-configurations xmlns="http://cisco.com/ns/yang/Cisco-IOS-XR-ifmgr-cfg"> <interface-configuration> ...
IOS-XE Ignore Radius VSA's
I was curious if on the Cat 9k series switches, is there a way on a port (or many whether individually or globally) to have the port ignore any VSA attributes sent back by the radius server. Like if I want to ignore the VLAN or the IBNS template tha...
| User | Helpful Count |
|---|---|
| 65 | |
| 55 | |
| 41 | |
| 35 | |
| 32 |
