Activity in Technology and Support
NAM to WNS migration / EAP-TLS with EAP-Chaining discussion
I am looking for experiences from others who have done a migration from Cisco NAM to Windows Native Supplicant. Especially if you use it for wired devices doing EAP-Chaining with EAP-TLS for both machine and user. I acquired an ISE environment tha...
iPhones unstable on wifi
Hi Folks,I am running EWC on 9115AXI Access Points. I randomly see that Apple iPhones are losing their Internet connection while they are sill on the wifi network. As a workaround I have to turn the wifi on the iPhone off an on again. This happens al...
Looking for SNMP OID for CPU Utilization on IOS-XE SD-WAN (cEdge)
Hi everyone, I’m currently working on monitoring Cisco IOS-XE SD-WAN (cEdge) devices through SNMP.However, I haven’t been able to find a valid OID for CPU utilization — the usual OIDs from CISCO-PROCESS-MIB or HOST-RESOURCES-MIB don’t seem to return ...
Phones bouncing between voice and data IP after reboot
I have Avaya 1140e phones with my Cisco 9k series switch, configured with voice and data vlan. NO ISSUESswitchport access vlan Xswitchport mode accessswitchport nonegotiateswitchport voice vlan XXdevice-tracking attach-policy IPDT_POLICYaccess-sessio...
Cisco 2130 Firepower FTD software upgrade failure
Greetings,We have a Cisco 2130 Firepower FTD that we recently attempted to upgrade the software version 7.4.2.2 to 7.4.2.3-4.Via the Cisco 2600 FMC, we ran the update via Setup - Product Upgrade - and selected the device. The package uploaded, the c...
Cisco Expressway SIP video call disconnects after 2 minutes
Hi there,I got a couple of Cisco Room Bars in our environment with Cisco Expressway Edge and Core. When we are in video call, the call disconnects after exactly 2 minutes. In Cisco Expressway Edge logs I can see the following message:481 Call/Transac...
Issues when updating admin password of an FMC-managed FTD via Ansible
Hi.We are currently facing issues when trying to automate the "admin" username via Ansible remote command execution.We have a Cisco Firepower 2130 Threat Defense Version 7.4.2.2 (Build 28) which is manged via our FMC version 7.4.2.3.Anytime we try to...
Cisco ACI ESG not showed up in Operational Tab
I am trying to configure a ESG.Conditions: 1. EPG operational status is fine ( IP and MAC learned ).2. ESG created with correct EPG selected. 3. APIC version 5.2(8g). Spine: N9K-C9336PQ,version 14.2(7f). Leafs: N9K-C93180YC-FX, version 14.2(7f). The...
Failover Ethernet1/11 (Failed - No Switchover)
Hi all!I have a question about ASA cluster failover. Failover LAN interface shows the following error:CGD600167DVPN1/sec/act# sh failFailover On Failover unit SecondaryFailover LAN Interface: Failover Ethernet1/11 (Failed - No Switchover)Reconnect ti...
Resolved! C9300L-24T-4X - Visio
Does anyone have a Visio stencil for the Cisco C9300L-24T-4X? Thanks in advance!
Resolved! BGP peering over two VPC paths in L3out interface profile
Hi all, I have the following situation:I want to create an L3out (SVI) and add a BGP peering. Since the SVI consists of both the 2 VPCs I add a new path to the Interface profile of the L3Out, with the same ip addressing scheme.My problem is how to cr...
Firmware
hello dear guys I need Cisco WAP4410N Access Point Firmware above 2.0.6.1thanks for help
Problems with EVPN Point To Point VPWS between IOS XR and XE
I am labbing EVPN Point To Point VPWS for my CCNP SPCORE test and I was able make it work between two routers with IOS XR NCS540, but when I tried to do it between IOS XR and IOS XE the P2P comes up and I am able to see mac address on the local CE of...
Local Web Auth on the AP
Is it possible to host a local web auth page on an AP? Can the embedded WLC function be used for this? This will be for 9176I APs. The client would like a local login page for guests but any authentication server will be physically located too far aw...
| User | Helpful Count |
|---|---|
| 191 | |
| 132 | |
| 94 | |
| 90 | |
| 76 |
