I have a small office network with an existing CBW150AX-E-EU AP. I'm trying to add another CBW150AX-B-NA AP to the same network. It is a single VLAN network with a switch and an ISP router with DHCP service.The new AP powers up and boots to a conditi...
We have a stack of IE 9320 switches as mentioned below:1) IE-9320-26S2C2) IE-9320-26S2C3) IE-9320-24P4S4) IE-9320-26S2CAll are in stack and in install mode and running IOS-XE 17.12.05When we power cycle switch 3 and switch 4 in the stack, it is takin...
Hello Cisco Community,The router Cisco 4321 gets stuck when trying to load IOS : isr4300-universalk9.17.06.05.SPA.bin and get the following error:%IOSXEBOOT-1-INVALID_IMAGE: (RP/0): Incompatible hardware and software image version; newer software ver...
In the last couple of deployments our APs lost their name when reconnecting to the 9800 after initial staging. This has happened whether we changed the name in the GUI or via the console on the AP. Anyone else seen this behaviour?
Hello guys,C2960 installed new iOS now it’s hung up Switch is WS-C2960-48PST-Sit used to have iOSFash:/c2960-lanlitek9-nz.122-50.SE4/c2960-lanlitek9-mz-122-50.SE4.bin"now I installed iOS"Flash:c2960-1anlitek9-mz.152-7.E12"from the picture I’m attachi...
I am trying to write a CLI Template using Velocity in Catalyst Center. I want it to run through a for loop for the amount of switches in switch stack (provided by the user, max up to 4), and provision the switches in the stack (switch x provision MOD...
Hello,Trying to test restconf I can ssh to the lab. Works fine.curl -k -u "<username>:<password>" host -v* Host <>:443 was resolved.* IPv6: (none)* IPv4: 131.x.x.x* Trying 131.x.x.x:443...Seems like something else might be blocking it. I am aware tha...
Hello, We have a couple of OCSP responder certificates expiring after 60 days. When I check the 'Issued by' column it has the name of one of the other node on it, which is the PAN. However, I am at a loss about how do I go further to renew it. There ...
Hi, One of our customers has a C9800-L-F-K9 HA pair running Cisco IOS XE Software, Version 17.09.05. They operate a BYOD SSID, which uses local WebAuth with custom webauth pages stored locally on the controllers: bootflash:/custom_webauth/login.htm...
Hello everyone,I need to send zeek logs to Cisco SNA (flow collector)According to the Cisco manual:“Format: The zeek log generator must add the zeek_filename="xxx.log" tag before the JSONL string for the Flow Collector.”I need help about, adding the...
Hi, I have a customer with CUCM 14SU1 who have deployed three VG410 gateways. As the CUCM version does not support the VG410 in the gateways drop down list with any protocol (SIP, MGCP or SCCP) I configured a SIP trunk and Route Patterns on CUCM and ...
Hope this helps someone. I went through a newly developed issue regarding Site to site tunnels. I had to make a new site to site tunnel between two sites. I routed all DNS through the tunnel to a DNS server on the other side until I could create a DN...
Is there a way to recover the credentials for an FMCv300? The individual who managed the FTDs/FMC left the organization and the folks that are supposed to now manage the environment cannot find the FMC credentials.
Hello awesome community!Continuing our networking fundamentals series, today we dive into Trunking!Learn how trunks carry multiple VLANs across switches, keep traffic separated with 802.1Q tagging, and form the backbone of inter-switch communication....
