Activity in Technology and Support
Dynamic mac from GigabitEthernet2 conflict with WlClient
hi.. i'm getting the following error %SWPORT-4-MAC_CONFLICT: Chassis 1 F0: cpp_cp_svr: Dynamic mac B827.EB64.23F0 from GigabitEthernet2 conflict with WlClient, please check the network topology and make sure there is no loop.QFP:0.0 Thread:000 TS:000...
Resolved! License need to Join AP to 9800 WLC
Hi Community,I am currently using a Cisco 9800-L WLC in my network, where 7 Access Points are already joined and working fine. I would like to add 6 more APs to the same controller.Could you please confirm whether I need to purchase additional licens...
Resolved! Renew Self-Signed Certificate on Cisco 9800
Currently have a 9800-40 w/ 100 APs associated and working as expected. The self-signed certificate used for AP Join is expiring next month and wanted to work on getting it renewed and replaced prior so as to not have any issues. I was reading this ...
IP Trusted List and Multi-tenant VOIP in CUBE
I have set up multi-tenant in my Cisco CUBE. I needed to direct sip sessions on different interfaces. My question is, can I establish an ip address trusted list for each tenant or does it always reference the global voice service voip configuration? ...
How to check the licensed throughput on Catalyst 8300 router?
Hi, how to check the throughput on catalyst 8300 router? Is the output of the following command representing the overall licensed throughput of the router or only represent the throughput of VPN only? Can someone pls advise? thanks in advance! I onl...
Resolved! ASA - Syslog Message List by Event Class?
Hey gang:I'm updating my logging lists and would like to know if there is a list of syslog messages by event class (I found the list by severity level). If not, is there some way to identify the class by looking at the syslog message number?Thanks.
CatCenter not displaying NETFLOW data from licensed 9500
I am trying to get the NETFLOW data from our 9500 Catalyst switches into CatCenter. Switches are running version 17.9.5We have tried using the workflow "Enable Application Telemetry" but that is not showing as an available option. This is an example ...
Linux EAP-TLS Authentication
All, I am trying to get EAP-TLS working on an Ubuntu Linux machine. The system is controlled by Centrify and Centrify has pushed out a certificate, private key and chain file to the machine. I am attempting to use the wpa_supplicant with the foll...
Catalyst sw-c4948 switch, Issue with bootflash
Hello there , By mistake I had formatted booflash as it is in dir Bootflash: result message for slot0 "The device has either been removed or bad device name Bootflash:" There is no Bootflash image in slot0, so I looked for a way to upload my image t...
NAT behavior on FTD
Hello Experts , I have some strange behavior on FTD as below : I have nat statement from inside to dmz1 :nat (inside,dmz1) source static obj_10.1.1.11 obj_192.168.2.28and with packet tracer i can confirm traffic sourced from 192.168.2.138 to 192.16...
Secure Access Management Tunnel XML File Name
Hi Its my understanding from previous machine tunnel configurations on ASAs/FTDs, that the machine tunnel XML profile name needs to be 'VpnMgmtTunProfile'. However, when I download the machine tunnel XML from Secure Access the file name is 'machine-t...
high CPU utilization on cisco switch 3750
Hi Cisco Team,i expereince the high cpu utilization in cisco switch 3750..please guideCPU utilization is about 35%..please let me know its normal or high
Cisco ACI License
Hi,,For Cisco ACI LIC plan, if I have 2 spines 9500, and 4 leaves 9300, and want full ACI features Which LIC should I use?Also is LIC subscription based or perpetual based?
Resolved! Talos Connectivity Problem
Hi to all ,i am getting many messages as the following:Severity: criticalModule: Talos CommunicationDescription: 3 modules failed:* URLDB- Failed to retrieve beaker inventory* LSP- Failed to retrieve beaker inventoryMy subscription is active (it expi...
New Always-On DevNet Sandbox for Cisco Catalyst 8000 & Catalyst 9000
Introducing the new Catalyst 8000 and 9000 Always-On sandbox labs. DevNet technical leader Joseph Kearns explains how to gain access to the these environments and how they can be useful for simple automation use cases. Key Takeaways Always-On Labs...
| User | Helpful Count |
|---|---|
| 194 | |
| 122 | |
| 92 | |
| 89 | |
| 76 |
