Hi everyone, I just deployed multiple about 40 APs (9120/30) Flexconnect WLC 9800. Several clients (Apple) are reporting disconnections, uppon a review of their Radioactive logs found a common denominator: 2020/12/14 19:45:08.125 {wncd_x_R0-2}{1}: [c...
Looking for recommendations for routing traffic from ASA back to router on "inside" network so we do not have to add static routes on systems. We recently added an ASR1001 to our "inside" network that routes traffic to Amazon thru a Megaport link tha...
How I setup on ASA to allow only specific IPs ( peer IPs ) to connect ASA by remote access VPN( IPsec VPN client S/W).Due to the remote access VPN, I had setup assigned IP to remote access VPN client during dialin.I try to use the IPv4 Filter, but ...
Hi,We have an ATA191 MPP we bought on Amazon (supposingly new) that is already locked to a voip provider. We can do a factory reset on it no problem, and do the setup config for our own needs (Freephoneline), but the minute we reconnect it on line, i...
Entitlement file generation failed. Please try again. If issue persists, find help in the communityI've triyng to generate a new CSP-C entitlement, but recieve this issue:Entitlement file generation failed. Please try again. If issue persists, find h...
Hello,I have a cluster of 3802i-k9 running ME 8.10.196.0 firmware.I noticed that at the top right corner of the web dashboard, it shows "configuration has been changed" even if you just simply have a look at those stats data and made nothing change. ...
Hi Cisco Community,I am fairly new to the Cisco Catalyst family and I have inherited a system which I need to upgrade/expanded/optimize.In this process I have come across a situation which is very strange (to my limited knowledge). Here it goes:I hav...
I need to change the IP on an MGCP VG 310 but can't find documentation that tells whether any changes need to happen on the Gateway section in UCM. Could someone point me to the documentation on this or let me know about any required changes in CUCM?...
Hello expertsI have a problem with an MPLS adjacency.I have an ASR900 connected to a 10Gb C9300, MPLS and OSPF are enabled in this interface, adjacencies are created and everything works.When the C9300 is restarted, the MPLS and OSPF adjacencies are ...
Have a situation where the user connects to the VPN with SBL (it connects fine), but when they login to the computer, they have to open Secure Client again and connect to the VPN all over. Thoughts on why it's not staying connected after workstation ...
Hi everyone, I have a new but configured basically Cisco 3560cx 12pd-s. I keep getting the dhcp conflict error messages everyday. I have an Asus GT AX-11000 router that is connected to my new Cisco 3560cx 12pd-s. I somehow managed to do a basic confi...
I have registered and have the "Customer Administrator" role and it has been well more than 24 hours (it's been several weeks) since the registration completed, yet I cannot use the portal. When I sign in, it tells me that I don't have access and ne...
Hi, I have a CP-8841 that is stuck on Verify Your Network Connection. IPv4 settings have been configured but the phone does not move past the Verify Your Network Connection message. I already tried factory reset and I also went into Settings/Admin S...
I have 8851 CISCO phone. UC is running on ISR 4331. Im configuring all settings in router through cli. When I run "create profile" in voice register global to create SIP phones xml configuration, this xml configuration is automatically generated with...
I'm looking to enable Ikev2 for anyconnect and disable SSL.My concern is on the change log when I go to deploy it, the IPsec Proposal says port 443.We nat Port 443 down to out on site exchange server for hybrid email.Our SSL vpn has been redirected t...
