Activity in Technology and Support
Mobility Express Upgrade Failure
Hello, I am in the process of updating a Mobility Express WLC from Cisco. I have deployed the TFTP server and the correct images and the pre-download worked on all access points except one. In the following picture you can see what output I get. I l...
Configuring NAT overload with vrf lite on a CAT9K
Good day;Need help with how I can configure NAT overload with an existing vrf on a CAT9K_IOSXE V16.12. This is what I am struggling with, I currently have a vrf called AWSDX-S3. Now what I am trying to do is I have added a L2 SW and ran trunk ports...
Installing Secure Client (5.x) AND Any Connect (4.x) on 1 computer
I have a weird situation I need to connect to two sepaate VPN (not at the same time).One of these requires Cisco Secure Client 5.x the second works with Any Connect 4.x.I have Cisco Secure Client 5.x installed, if i try connecting to the VPN that use...
Changing wsa data ip
Hi all,We had WSA appliance and we are migrating appliance to virtual environment.We have configured new WSA and tested and its working fine and now we are planning to move it to LIve so we are planning to change the data ip.of new virtual WSA to the...
10mb connections
Hello,On the newer switches with 2.5/5gb ports how do you handle devices that only work with a 10mb NIC?We have a HVAC controller that only has a 10mb NIc on it so the switch doesn’t detect it. Is there a device that will convert down to 10mb like a ...
Trunking an ip addressed inside interface on Firepower 2130
My network endpoints use the IP addressed vlans on my core cisco layer three core switch as their gateway addresses. i.e.- vlan 11 endpoint address 192.168.11.3/24 with gateway 192.168.11.1/24 (vlan ip on core) and vlan 12 endpoint address 192.168.12...
Client status locked in "Web Auth Pending" on WLC 9800-40
Hello all, I'm having an issue with clients connected on my Guest SSID configured with Web Authentication Splash Page. Basically by today (NO CHANGES NOR ACTIVITIES WERE DONE) all the clients which are trying to connect to this SSID cannot reach th...
One-way Audio following IP Address Change
I've recently inherited a new network as part of beginning a new job. Historically, my exposure to voice is pretty limited. Without getting into the details of what lead to it, as it's not relevant, after performing a reset on an 8851, the phone gr...
Need help - your account has been suspended
Hi, I can barely make this post so I'm writing it very basically.I'm getting this error (in the title) when trying to start a webex meeting.May anyone please help?
vfmc-7.4 cannot deploy ovf
Dear TeamI have downloaded the vfmc for esxi 7.4.X and 7.3X but i cannot deploy in VMware after deployment its retturn "operating system not found"any ideaRegards
Resolved! A question about MAC addresses for access points
Can anybody tell me what exactly is the difference between the radio MAC address vs the ethernet and Wi-Fi mac addresses? What is the purpose of the radio MAC address? Apparently, wireless access points don't just have an ethernet and Wi-Fi MAC, but ...
CUCM Trace Logs Limited to the Previous 10 Minutes Worth of Calls
This is a 2-server cluster of CUCM 12.5It is a small deployment of around 100 phones that don't handle a large volume of calls.I'm pulling logs for the CallManager service.Typically I would expect to be able to go back at least weeks but I can't pull...
redundancy in core layer
hi guys . i have a network with below topology. In the core layer, I want to have redundancy, which means that if the main core switch of my network has a problem, the backup switch will automatically enter the circuit. What method is there?
Can anyone explain “last active” and “last registered”
Cisco Unified CM AdministrationSystem version: 12.5.1.13900-152Can anyone explain “last active” and “last registered” on call manager, Find and List Phones page?It’s my understanding that “last active” displays the timestamp when a device was last ac...
Can you read the contents of a message that is in quarantine?
Can you read the contents of a message that is in quarantine? If so, how would I go about viewing it? Thanks!
| User | Helpful Count |
|---|---|
| 108 | |
| 80 | |
| 79 | |
| 70 | |
| 59 |
