Activity in Technology and Support
Can CUCM be used to route calls between different sites?
I'm involved in the following setup illustrated below. I am Site 4. I have a SIP trunk via the CUBE to Site 3. Calls route between Site 4 and Site 1 with no problem. Is it possible to use Site 1 CUCM to route calls from Site 4 to Site 3 or 2? Is it p...
Unable to get console access on switch 3850 - Blank terminal
Hello,I have a switch I am unable get a prompt on the console port.I can SSH to it, and have confirmed that the baud rate and stop bits are correct from the console switch. There are two other switches that I can console to.The differences are that t...
Command to poweroff/shutdown the leaf and spine switches?
Hi Team,Can anyone please help me in powering off the cisco Leaf and spine switches? ThanksRajan
[EDIT] How to retrieve the portal ID of a guest account?
We have two ISE ecosystems different and isolated (2.7 and 3.2)I must migrate guest accounts from one system to the other one.On 2.7 we have two sponsorportals and so it is on 3.2.I managed to retrieve captive portal users through a python script of ...
SSH OVER HTTP PROXY WSA
Hello,A client is trying to SSH through the HTTP proxy (WSA), it works but the response times are huge.ssh_args = -C -o "ProxyCommand=nc -X connect -x proxy-http:8080 %h %p"It serves its purpose. HTTP proxy isn't designed for that, but has anyone tri...
Need some assistance with some basic VLAN/Routing config Cisco 1941.
Hi all I'm setting up a CISCO LAB to keep me busy in my retirement. My Current network consists of a TP-Link Deco mesh network which works well for my IOT, PCs and internet access. I just got hold of a Cisco 1941 router with a EHWIC D8SGP module. ...
Resolved! modification of Unified CM Telephony Provider in uccx,greyed out
Hello everyone,I have uccx 12.5 installed and integrated with CUCM 12.5.This uccx was redundant for a long time (2years ago).I have a new cucm 12.5.i want to integrate the new cucm 12.5 with the uccx.I wanted to modify the Unified Telephony provider ...
Issue with VTP *** MD5 digest checksum mismatch on trunk: Po1 ***
Anybody can help me with this issue on VTP?
Difference in licensing between S195 and new s196 missing WSA-L4TM-LIC
Question, attempting to help a customer with the new S196 and we have found that the new S196 doesn't appear have the WSA-L4TM-LIC license like the old S195 did. Is this feature now included in the new Subscription license? Thanks, Seth
Disable SIP ALG on Firepower 1010 by Web or Telenet
Hey allI have a Firepower 1010, I need to disable the SIP ALG on it, I have access to the Web Client and Telenet access to make changes, can someone give me an easy way to make these changes, I don't have the ASA Software that could access with.
AnyConnect Microsoft Teams & Skype Packet loss
Hi Guys,We're having some issues since deploying the AnyConnect VPN with users reporting poor call quality and packet loss on Microsoft Teams and over Skype both audio and video calls?Is there anything we can try or tweak on our ASA and AnyConnect se...
Cisco 9300X Static routes don't work to SVI Tunnels
NOTE: I have done the same test setup with 4000 series routers, and routing works fine.I have successfully setup 3 SVI (Static Virtual Interface) tunnels with IPSEC between 2 9300X switches.- I can ping the tunnel IPs- I can ping each VLAN interface ...
Query regarding BGP convergence on FTD HA pair
Hi, I'm looking at deploying BGP on an FTD Active/Standby HA pair (FTDs are 4215 hardware running 7.2) to enable routes to be controlled by neighbouring routers rather than relying on 100s of static routes on the FTDs. I was wondering if anyone could...
C9105AXW-B Office Extend AP broadcasting personal SSID w/ IOS WLC 17.9
Hello, I have a C9105AXW-B access point configured for office extend. When the AP is joined to an AireOS WLC (8.10.185.0) in office extend it doesn't broadcast a local personal SSID. When I join the AP to an IOS WLC (17.9.5) in office extend mode I...
What is the minimum port configuration necessary to profile host?
Hello,If I simply want to profile network hosts without subjecting them to dot1x, what is the minimum port configuration necessary to accomplish this?
| User | Helpful Count |
|---|---|
| 100 | |
| 79 | |
| 73 | |
| 62 | |
| 60 |
