Activity in Technology and Support
CMX - cmxadmin password recovery 11.0
I am following this document to recover and reset the password for "cmxadmin" https://www.cisco.com/c/en/us/td/docs/wireless/mse/11-0-1/cmx-config/b_cg_cmx1101/performing_administrative_tasks.html#id_131101 When I reset my VM Server and edit ("e") in...
IPSEC VPN
Hello Team,I have below topology : -I have ipsec vpn from on-prem to aws cloud. the two endpoints [192.168.40.10/32, 192.168.30.10/32] work fine as they are allowed on the encryption domain.I have users using remote vpn to connect to on-prem dc to a...
Duo Desktop not recognized
Hello, I am using Cisco Anyconnect to connect to VPN. The system is using Duo Desktop for device health. It is already installed, running and all the checks are ok. However, I am getting this error message and not able to proceed: Install Duo Desktop...
Multipod L3Out Preference
Hi All,I'm currently deploying ACI Multipod with two pods.I've configured a single VRF and single BGP L3Out that connects the leaf switches within each pod to our core network. This L3Out is then assigned to each BD which results in the the associate...
Any Network Administrators who I can interview tomorrow?
Hello, my name is Matthew(19M). I have a First Year Experience class project where you are supposed to interview someone in the field that you want to partake in and mine happens to be a Network Administrator. I have tried for hours to find somebody ...
CISCO WSA upgrade alert error
We have upgraded our S1000v(wsa ) from 14.5.1 to 14.5.2 and upgrade was successful but when we checked the alerts we found an alerts as An application fault occurred: ('heimdall/svc.py send_command|195', "<class 'heimdall.exceptions.unknownprocess'="...
cannot get to privileged enable mode via console
After searching through other posts, my config seems OK but still strange behaviourasa 9.20 running on FPWR chasisI cannot get in enabled mode when connecting to ASA via console.It used to work but stopped after I played (disable and restore) with aa...
Repeating syslog Message and then Crash
We're seeing a continuous string of the following messages on a 9407 running 17.9.5. Eventually the switch crashes. I can't find any info on what these messages mean exactly and whether we're looking at a software or hardware fault. The supervisor...
The operation took longer than expected.
I have just synchronized both Active Directory and Cisco ISE, ISE is using my server (AD) as an NTP server, everything is fine, but now I'm facing an issue "Status Summary: The operation took longer than expected. This may be caused by slow network c...
Anyconnect Linux aarch64 (arm64) version?
Hello,While there are linux x86_64 versions and Windows arm64 versions:https://cios.dhitechnical.com/Cisco_Firewall_ASA_FTD/Anyconnect%204.x/anyconnect-all-packages-4.10.08029-k9/are there any plans to release a linux aarch64 (arm64) version?This wou...
PyATS fails to connect to APIC using rest.connector.Rest
Afternoon everyone, I'm trying to connect to an APIC using PyATS and the rest.connector.Rest method, but no matter what, I get authentication failures. Here is my testbed file:devices: apic: os: apic type: apic custom: abs...
Trunking an ip addressed inside interface on Firepower 2130
My network endpoints use the IP addressed vlans on my core cisco layer three core switch as their gateway addresses. i.e.- vlan 11 endpoint address 192.168.11.3/24 with gateway 192.168.11.1/24 (vlan ip on core) and vlan 12 endpoint address 192.168.12...
wireless authentication
hello I am working in an environment where there is a wireless guest infrastructure configured guest users are given access by an Administrator based on their email there is a requirement for a wireless printer to be given access to this guest net...
Resolved! How can i match vsmart with each Tenant
Hello team Last day i upgraded all controller in to 20.3.5 -> 20.6.5 version as you know in 20.3.5 which use multitenant mode , the vsmart are bind in each tenant. but when i upgarde it 20.6.5 version. the vsmart are come out side. I want to use th...
Unable to Access Web Server - Whats Wrong with this Configuration
ASA working in IPSec, I am able to access HQ from UNIT No problem. Internet is only allowed on specific IPs which are outside DHCP Scope. When I assign IP for internet, now Internet is working, HQ Network is accessible, but S_EXT (webserver - 10.10.1...
| User | Helpful Count |
|---|---|
| 112 | |
| 111 | |
| 86 | |
| 65 | |
| 63 |
