Technology and Support

Resolved! mac flapping

Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1/1/2Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1...

Resolved! Cisco 9300X Static routes don't work to SVI Tunnels

NOTE: I have done the same test setup with 4000 series routers, and routing works fine.I have successfully setup 3 SVI (Static Virtual Interface) tunnels with IPSEC between 2 9300X switches.- I can ping the tunnel IPs- I can ping each VLAN interface ...

Spaces Telemetry issues

I'm trying to get environmental stats back from 9136/9166 on Spaces. I've imported the maps successfully and have enabled the IOT service in spaces. I'm still getting errors for the TDL Telemetry under the troubleshooting section which seems to be pr...

routing failed to locate next hop for TCP - Anyconnect

Hi All, I configured anyconnect vpn in ASA and its working ok. I enabled ASDM access in inside interface (10.10.50.254). After connecting to VPN, i tried to ping and connect to ASDM on 10.10.50.254 but its not working and i get "routing failed to loc...

Webex registered with UCM – E911 settings missing when on-prem

I am using Webex registered with UCM.Webex app version 44.4.0.29298UCM Version 14.0.1.13900-155 When I use Webex over MRA, the E911 settings button appears and I can configure my location as expected.But when I am on premise, the E911 settings button...

Cisco AnyConnect Umbrella Roaming Security Module

Hi,So was reading up a lot on the difference between the Cisco Anyconnect Roaming Module vs the Umbrella Roaming,Its clear that best practice is the Cisco anyconnect option as UR is EOL in a few months, so we recently deployed the new client company ...

FMC objects list - flipping through pages is difficult

Hello!I´m using FMC 7.2.5.1 in Edge browser on a 1920x1080 screen with 75% zoom in the browser.When I open "Objects", the table of Network objects is shown.When I want to start flipping through the pages to find something (because "Why can´t I just s...

Risport70 selectCMDeviceExt does not return CTI Port status

I am trying to retrieve the registration status of phones and CTI ports on CUCM using Python. To do this I am first running the CUCM AXL query listPhone to get a list of all phones I'm interested in. Then I pass this list to the SelectCmDeviceExt RIS...

Resolved! Embedded Packet Capture failing to export

I am using the Embedded Packet Capture feature on a C8200L-1N-4T router.I have the capture and need to export it to our TFTP server.When i run the following command:8200_RTR#mon cap DMVPN export tftp://192.168.1.146/Community.pcapI get the following ...

CUCM Trace Logs Limited to the Previous 10 Minutes Worth of Calls

This is a 2-server cluster of CUCM 12.5It is a small deployment of around 100 phones that don't handle a large volume of calls.I'm pulling logs for the CallManager service.Typically I would expect to be able to go back at least weeks but I can't pull...

MTU for SVL

Is it necessary to change the MTU for SVL links in a scenario in which interfaces are configured with MTU larger than default 1500 bytes?Traffic could flow between chassis through SVL links in a Stackwise Virtual cluster. Could not find any reference...

FTD: Again - Unable to reach Cisco Cloud from the device

Hello everybody, our customer is using the FMCv rel. 7.2.5.1 and many FTDs.After de-register/re-register the FMC in the Smart Software Manger because another error message four devices (7.0.1 & 7.0.5) fourdevices show the error: Threat Data Updates o...

Created a Route Based IPSEC Tunnel on Cisco FTD 2140

I have a Cisco FTD 2140 Secure Firewall that I am trying to build a route based IPSEC tunnel using VTI's. The vendor needs my proxy ID or encryption domain to be presented as a public IP address. So my WAN IP is obviously public but my internal netwo...

Webex registered to UCM – Voicemail Credentials Rejected

I am having an issue with Webex registered to UCM where I cannot login to the voicemail service.Both Unity and UCM are LDAP integrated, so it’s the same credentials for both. Unlike Jabber, Webex does not let us directly configure the voicemail crede...

Answer phone

I have headset Bluetooth paired with cisco phones and working fine, but auto answer not work. I tried to enable Auto answer with headset on DN but still any incoming call on phone not auto answer, is there anything I miss other than configure auto an...

Technology and Support

Browse the Community

Certified Remanufactured Equipment

Cisco Software

Cisco Start

Collaboration

DevNet Hub

Data Center and Cloud

Internet of Things (IoT)

Networking

Online Tools and Resources

Security

Service Providers

Services

Small Business Support Community

Wireless - Mobility