Activity in Technology and Support
CX Cloud on Multi Cloud
How about the CX Cloud on Multi Cloud environments?
CSR1000 how to quote a license renew
Hi I have a customer that sees the following on its Smart Account: What do I have to quote to renew their expiring licenses? Alberto
Spaces Telemetry issues
I'm trying to get environmental stats back from 9136/9166 on Spaces. I've imported the maps successfully and have enabled the IOT service in spaces. I'm still getting errors for the TDL Telemetry under the troubleshooting section which seems to be pr...
Cisco NSO Service Rollback File Id
Hi experts,Does anyone knows if it is possible to get the rollback file id inside of the service callback like post-modification etc.?If not do we have a way to get this file for a particular service?Thanks and Best Regards ...
SRTP config
Hi All, I'm trying to establish a SIP trunk to an ITSP using TLS and SRTP. We think we have done all the trust point stuff and TLS seems to be OK. However, I'll a little lost on the SRTP. Looking at several guides looks like a few different methods. ...
Issues migrating APs from 1 WLC to another
I need to upgrade the software on an AIROS WLC. We have a backup WLC that already has the new code. My plan was to upload the new code to WLC 1, predownload code to all 2,000 APs, then migrate all the APs to WLC 2 by using a DNAC job to tell the APs ...
Snort3 not recognising SMTP/S but Snort2 did/does !?
I'm in the process of updating all our FTD's from Snort2 to Snort3 & almost everything appears to work, except SMTP/S email.Under Snort2 it shows in event logs as SMTP/S Client traffic type correctly, but when Snort3 is enabled, it does not recognise...
Created a Route Based IPSEC Tunnel on Cisco FTD 2140
I have a Cisco FTD 2140 Secure Firewall that I am trying to build a route based IPSEC tunnel using VTI's. The vendor needs my proxy ID or encryption domain to be presented as a public IP address. So my WAN IP is obviously public but my internal netwo...
Weak SSL/TLS Key Exchange
Hi I hope your doing well in our network infrastructure where we have Qualys to scan for vulnerabilities i can't find a solution for this certain vulnerability here are the details :Weak SSL/TLS Key Exchange impact an attacker with access to suffici...
Enable snmp v3 command
I want to enable SNMPv3 on a Cisco router, v1/v2 is fine but v3 refuses to work. Can you help?
Posture Logs
Hello,In the AnyConnect client under the "Scan Summary" tab, it shows the names of the posture checks as they are defined in ISE. Is there a log on the workstation that will actually show WHAT those items in the Scan Summary are actually looking at?
Push2Phone - Send Text to Phone
I have created a push2phone program in asp.net that allows for sending text messages to phones, and I was unable to find a free one online so I created my own. I have it working on call manager 4.1(3). It might work with other versions as long as the...
Resolved! Cisco 9300X Static routes don't work to SVI Tunnels
NOTE: I have done the same test setup with 4000 series routers, and routing works fine.I have successfully setup 3 SVI (Static Virtual Interface) tunnels with IPSEC between 2 9300X switches.- I can ping the tunnel IPs- I can ping each VLAN interface ...
9200L - Can't convert from bundle to install mode. Commands are not recognized.
Working on a stack of new Catalyst 9200L-24P-4G switches. This is the first time with this model and am beyond frustrated at this point as none of the documentation seems to work. Currently, all 4: Switch Ports Model SW Version SW...
One of the stacked switch goes to enable mode without password (9200L)
Hi,I have a problem with stacking two cisco 9200L's, after stacking, one of the pair goes straight to privileged exec mode, without enable password, while the other needs password for it. It's not the first time, this occurs, do you have any idea whe...
| User | Helpful Count |
|---|---|
| 103 | |
| 79 | |
| 76 | |
| 63 | |
| 61 |
