Activity in Technology and Support
how to onboard the SDA Fabric Edge which is using stackwise virtual
Hi , Thank you so much . Does anyone have any idea how to onboard the stackwise virtual into fabric , as of today LAN automation is not supported.Im thinking of below approach , really appreciate your valuable suggestions. 1> Manually configure the...
Resolved! ISE admin Group AD users
I have created an external admin group in ISE, which is pointing to an AD group. There are several users in this AD group.Will all the users in this AD group gets ISE admin access or can it be restricted to few users.
IPSec VPN Tunnel Lan-to-Lan decrypt count zero
Hi, I have one issue with IPSec tunnel Lan-to-Lan between ASA 5525x (v9.8) and ASA FPR 2110 (v9.16). My Tunnel is up but ping between each client was not successful. Both peer status sh cry isakmp sa in "MM_ACTIVE".I ran packet-tracer icmp between pe...
Retrieve Serial Number Info for Cisco WAP4410N Access Point
Hi,I have tried to retrieve serial number info for 3 units of the Cisco WAP4410N Access Point devices via Web GUI and CLI, but it seems can't find the serial number info for this model. Kindly advise further, thanks.Regards,Wilson Leong
NCS-55A1-24H safe upgrade path from 6.6.3 version
Hi everyone,I tried to upgrade IOS-XR from the 6.6.3 version to version 7.6.2 on NCS-55A1-24H and the upgrade failed. I presume that upgrading to version 7.6.2 requires upgrades to lower versions of 7.x IOS-XR as a first step. If that's correct, I wo...
Software Patching and Updates
Hi all,The license of Cisco Switch has lapsed. Would it still eligible to obtain software updates and subsequent patching? As my current Cisco Switch did not renew the license while looking the trend of new vulnerabilities arising from time to time. ...
WLC 9800 Process iosd Eror
hello,i'm running wlc9800-40 17.6.4 version and i'v got this errorSeverityProcess NameMessageCriticaliosdApr 10 23:47:04.326: %IOSXE_QFP-2-LOAD_RECOVER: Slot: 0, QFP:0, Load 45% recovered.5 secs traffic rate on QFP: Total Input: 13034 pps (13.0 kpps)...
Recommendation Software ISE
Hi EveryoneOur client for ISE software still uses version 2.6 with pach 10,We will upgrade the software to 3.1 with patch 8, please provide a recommendation link from CiscoI'm afraid that if I downloaded it wrong it would have fatal consequencesThank...
Cisco DNA Center Telemetry
Hallo All! What is the reason that when enabling Telemetry on C9300 Series Switches, only Application Name, Usage and Througput are shown? Switches configured with telemetry show only Application Visibility (Name and Throughput) in DNA center. Why is...
Please explain those terms. I can't understand. Help needed!
"Distribution Switch for Formation" & "Enterprise and Active Directory (AD) Zone Switch"
9800 Guest Anchor Design
I am trying to understand Guest Anchoring with the 9800 Controllers. In the 5500 series WLCs you had to access the WMI from the inside network through the firewall to the Anchor Controller Mgmt Vlan on a DMZ. Then create another sub-interface on the...
Why VLANs are not being shown?
Greetings!So I was practicing to configure VTP and VLANs. For a start, I created 3 switches (only 2 being turned on). The trunks are working fine as the switches are able to acquire an IP addresses via dhcp from a dedicated router and vtp appears to ...
RADIUS server and 802.1x on switch Cisco Packet Tracer
Good afternoon, Cisco community. I faced a problem when configuring RADIUS server using switch as authenticator. When using router everything was not complicated and worked, example below.But my supervisor said that it is wrong to do it this way and ...
VRRP issue
Facing issue with VRRP, when upstream router5 initiate traffic for downstream router6 then return traffic is not following VRRP VIP as Gateway. In my case switch2 is master and switch3 is standby.If Router6 initiate the traffic then VRRP working fine...
My Cisco Nexus Swith 6001 is stuck in bash mode
My Cisco Nexus Swith 6001 is stuck in bash mode and giving below error.system is coming up.....please wait.......This issue happens after power outage happened. We have reboot switch many times and used multiple username/passwords but its not appeari...
| User | Helpful Count |
|---|---|
| 98 | |
| 78 | |
| 73 | |
| 62 | |
| 58 |
