Activity in Technology and Support
Configuring NAT overload with vrf lite on a CAT9K
Good day;Need help with how I can configure NAT overload with an existing vrf on a CAT9K_IOSXE V16.12. This is what I am struggling with, I currently have a vrf called AWSDX-S3. Now what I am trying to do is I have added a L2 SW and ran trunk ports...
SSH OVER HTTP PROXY WSA
Hello,A client is trying to SSH through the HTTP proxy (WSA), it works but the response times are huge.ssh_args = -C -o "ProxyCommand=nc -X connect -x proxy-http:8080 %h %p"It serves its purpose. HTTP proxy isn't designed for that, but has anyone tri...
Resolved! How can I edit a Switch Upgrade Group in ACI v5.1+?
Hi experts. I'm struggling with the abysmal user interface experience introduced in ACI v5.1 for upgrading switch firmware. Having managed to blunder through an upgrade about a year ago using the new UI, I am now at the stage where I have my two upgr...
Rebuild Cisco ACI with a new version
Hi, we have a Cisco ACI in our LAB enviroment with an older version 2.2. We'd like reset/clean all the fabric (n.3 APIC,n.2 Leaf and n.2 Spine) and restart with a new version, the 5.2. Our hardware support it We don't need the backup of actual config...
Resolved! How to disable mac address in 9800 WLC
Hi Guys, As we know, there is option in Cisco 5520 WLC to mannualy disable any Mac addresses of user to deny network access to him. Is there any disable mac address option in Cisco 9800 WLC?
Lost ARP Announcement Packet for Meraki MR30H Access Point
Hi,I have a setup with following components.* Cisco - Meraki MSS120-8FP Gigabit Ethernet Switch* Cisco - Meraki MR30H Access Point (POE)* GRMS Device with LwIp Stack* 2 PC with Windows 10.* My PC (Windows) to pingWhen I try to ping the GRMS device t...
Resolved! Virtual WSA sizing
Hi, Anyone able to guide through a few sizing numbers for S300v/S600v/S1000v? Currently under an incident that the 4 x S300v keeps crashing under a certain load and TAC believes it is the loading issue. However, they don't follow up with the rec...
Cisco anyconnect browser ERR_SSL_Protocol_ERROR
Good day to everyone.I have two Cisco ASA running on FPR2130 assembled into a balancing group, for example:vpn-gw1.example.comvpn-gw2.example.comgeneral address vpn.example.com.Firmware version 9.18.3.56Anyconnect 4.10.07062At the moment, all our emp...
Blocking Mid-Call Signaling from CUCM SIP Trunk
Hi there, Lately, we have had many customers complain about intermittent call drops for external call transfers, no music on hold, and at times no audio at a resume on the SIP trunk we have from an ITSP. The problem would sometimes surface with cert...
ASA5516 Recommended software version
I am configuring ASA5516 from scratch and trying to find out the current recommended versions.Could you please advise?Curretly:ASA Software Version: 9.8(2)Firepower Extensible Operating System Version: 2.2(2.52)Device Manager Version: 7.9(2)152
Cisco Packet Tracer 2960-24TT indicates Orange (amber)
Hello everyone. I work in Cisco Packet Tracer and have a simple network with 5 subnetworks connected through 2960-24TT Switch. The problem is when i connect 5 subnetworks to 1 network some (3) routes light orange (amber). And i can`t fix it. Where sh...
FMC objects list - flipping through pages is difficult
Hello!I´m using FMC 7.2.5.1 in Edge browser on a 1920x1080 screen with 75% zoom in the browser.When I open "Objects", the table of Network objects is shown.When I want to start flipping through the pages to find something (because "Why can´t I just s...
EEM scripting help
I'm trying to have EEM script where I run the script manually and it display the output of the results in the session but for some reason I'm unable to do so. This is what I have so far(config)#event manager applet TestCommand(config-applet)# event n...
Using device templates to standardize configurations
Hi I'm running NSO 6.1.7.1 with juniper-junos-nc-4.12 NED.I'm trying to use NSO device templates to standardize certain parts of device configurations.In this particular case I'm trying to force a certain set of "apply-groups" on a given Junos config...
Resolved! Allocating DID's in CME
Dear All,I have both Cisco & Non-Cisco IP Phones which are reigistered in my voice gateway. Now i have got ISDN with DID's. How can i allocate some DN with DID number in order to call in both ways ( each extension 5000 calls outside, its DID should g...
| User | Helpful Count |
|---|---|
| 108 | |
| 81 | |
| 79 | |
| 66 | |
| 59 |
