Technology and Support

query on ASDM access

We have FTD devices with ASA image in production which managed by FMC and Also we are managing firewall through ASDM. so now we are removing the FMC from production and want to manage the FTD devices locally. so is there any impact if the firewall is...

Why Is Allegiant Air Phone Number Busy Always?

Phone assistance: One of the quickest ways to speak with a Allegiant Air support agent is by calling +ퟭ(ퟱퟳퟯ) ퟲퟬퟲ-ퟰퟱퟮퟬ .// +ퟭ(ퟱퟳퟯ) ퟲퟬퟲ-ퟰퟱퟮퟬ . The phone number for Allegiant Air assistance is listed on their official website. Simply call the number and...

Resolved! Webex Room Kit Mini w/TelePresence Touch not getting IP address

Main issue: The Webex Room Kit Mini is pulling an IP address, but the TelePresence Touch unit, which is connected to the Room Kit's dedicated Touch port (which I assume acts at least as a pass-through network port) is not (it's getting a 169.254.x.x...

Trouble with ASAv anyconnect radius login

Hi EveryoneI'm using a trial version of ASAv and i believe it has full functionality but is limited in 100kbps. I'm trying to set up remote access anyconnect vpn which authenticates to our NPS radius server. As you can see in the radius debug, it see...

9200L - Can't convert from bundle to install mode. Commands are not recognized.

Working on a stack of new Catalyst 9200L-24P-4G switches. This is the first time with this model and am beyond frustrated at this point as none of the documentation seems to work. Currently, all 4: Switch Ports Model SW Version SW...

Can anyone explain “last active” and “last registered”

Cisco Unified CM AdministrationSystem version: 12.5.1.13900-152Can anyone explain “last active” and “last registered” on call manager, Find and List Phones page?It’s my understanding that “last active” displays the timestamp when a device was last ac...

uccx - CUIC 12.5.1 - Repors: Chart with abandoned call total

Hello world,I am working on creating a custom report based on the stock reports available for our call center. We would like to total the abandoned call for each day, sorted by the hour of the day. I cannot seem to create a report that only shows th...

ISE is Profiling an IP Phone Incorrectly?

Hello All, Cisco ISE: v2.0.0.306Switch: 3560 IP Phone: 7941G I have had many other 7941G IP Phones connected to this switch, which have all profiled/authenticated correctly. The only difference between those phones and this one, is that this phone...

Enable snmp v3 command

I want to enable SNMPv3 on a Cisco router, v1/v2 is fine but v3 refuses to work. Can you help?

ISR 1100 Licensing

Picked up an ISR 1100 2nd hand for the lab, Will it functionally work without smart licensing being activated or will it run on an eval licence? Being a while since i touched smart licensing but last time i used it Cisco weren't enforcing it.

What abbreviation to use for Cisco Catalyst Center?

After upgrading DNA Center to Catalyst Center I have trouble finding a decent abbreviation to use for dns entries and so on(3-4 letters)...DNA Center was dnac which was simple and unique enoughCCC (cisco catalyst center) is out because its a shoe bra...

I'm going to Cisco Live 2024! What can I expect as a Cisco newbie?

Hi all,Thanks to some generosity from Cisco and from my university, I'm headed to Vegas for Cisco Live this year! I am very excited for the opportunity, but also a bit nervous considering my level of experience. I am only a freshman in college withou...

Sip trunk between cucm with cucm and cucm with asterisk

I have a trunk between cucm 6.1.5 and asterisk but when a call is made from cucm to asterisk it disconnects immediately it is picked (call from asterisk to cucm is ok). But it is working with cucm 10.5. I try route call from cucm 6.1.5 to 10.5 then c...

Unable to ping between two tunnel points

Hello, I built using the packet tracer a simple topology of three routers with ospf routing. I created a tunnel between the two routers that are not physically connected to each other, but I can't ping between one end and the other. I managed to ping...

Resolved! C220M - SNS-3595-K9 invalid signature detected

Hi,Our old ISE C220M - SNS-3595-K9 is migreted to new one and I am trying to use it for labb by installning ESXI on the old ISE. But everytime i am trying to boot by usb, I got a messege "invalid signature detected - check secure policy boot in Setti...

Technology and Support

Browse the Community

Certified Remanufactured Equipment

Cisco Software

Cisco Start

Collaboration

DevNet Hub

Data Center and Cloud

Internet of Things (IoT)

Networking

Online Tools and Resources

Security

Service Providers

Services

Small Business Support Community

Wireless - Mobility