Activity in Technology and Support
Adding Backup ISP
I have a pair of ASAs that I try to add a backup ISP. I would be creating sub interfaces on Gi0/0. Once I default the Gi0/0, the Outside configuration would be gone from the configure, can I do the sub interfaces. configure Gi0/0.10 with nameif Ou...
Why we need 6GHz Standard Power and AFC
By now everyone should have heard the news on 6 GHz and Wi-Fi 6E that was announced initially back in April of 2020. Customers have been deploying and turning up these networks on Wi-Fi 6E AP’s operating under LPI (Low Power Indoor) rules for many ...
Need a complete guide for WS-C2960X & how do i configure policing/qos
Where do i find the complete guide on my switch?This is the model number WS-C2960X-48FPS-L.The software version is c2960x-universalk9-mz.152-2.E3What I'm looking to do is limit how much bandwidth is allowed on an interface. The network at that site o...
Cisco sfp module rj45 brand connectors
I have a cisco sg350-10 switch with 2 sfp modules.Which brand suggestions would be compatible modules for a sfp rj45 connectors?can you send me the link of the manufacturer , brand or model suggestions?Any help would be appreciated.Thanks.
CIMC CLI Command Injection Vulnerability || CVE-2024-20295
We have Cisco Hyperflex nodes model “HX240C-M4SX” in our environment. Could you please let us know if the subjected vulnerability is applicable to this model.If yes, could you please share the fix as well.
QOS for a Destination-ip in Cisco IOSXE
Hi All,We have a URL which resolves to particular public ip and performance of that website is slow than expected from our office . We have a P2P link from office to DataCentre and from DataCentre it exits to internet. We observed the performance was...
Policy Based IPSEC Tunnel With Firepower
If I am configuring an IKEv1 IPSEC site-to-site VPN with an FTD device running 7.4.1 managed by the FMC and it is policy based, not route based, does the system ACL applied to the device also control the traffic across the tunnel? If so, then what Zo...
Puzzling results when pasting in ACL config to switch
Hello, I was creating 2 decently large ACL's to match some traffic today and I noticed something peculiar that has me puzzled. My first ACL has approx 90 ace's and pastes them fine. When I go back and look at the ACL, it looks like there are only lik...
IPSec VPN Tunnel Lan-to-Lan decrypt count zero
Hi, I have one issue with IPSec tunnel Lan-to-Lan between ASA 5525x (v9.8) and ASA FPR 2110 (v9.16). My Tunnel is up but ping between each client was not successful. Both peer status sh cry isakmp sa in "MM_ACTIVE".I ran packet-tracer icmp between pe...
Resolved! Best way to integrate ASA/ISE/Azure AD for MFA?
I want my VPN users on a Cisco ASA to authenticate against ISE but use Azure AD for MFA on the backend. So far, it seems there are three ways to do this. My requirements are that I must use AnyConnect and ISE. Setup Azure AD as External Radius Server...
Static Routes on FTD 2130 using CLI
Has anyone Created statoc route on the FTD sensor via the CLI?Mine looks like it goes throught bu when i FDM into it, i do not see them. Any Advice will be appreciated.Thanks.
redundancy in core layer
hi guys . i have a network with below topology. In the core layer, I want to have redundancy, which means that if the main core switch of my network has a problem, the backup switch will automatically enter the circuit. What method is there?
Resolved! I want to advertise only specific OSPF routes.
The route learned by OSPF from the LAN is re-distributed to OMP for publicity to other sites.I do not want to advertise the specific routes from OSPF. What kind of 'configuration' should we use ?I want to control this in the SD-WAN Router side, not t...
Setting a GRE tunnels between a NAT to a public IP.
Hi everyone.. i have been looking through multiple posts on the forum for similar cases but have not found the answer Im looking for.. I've been primarily using this thread for guidance. https://community.cisco.com/t5/networking-knowledge-base/settin...
cisco lock
hey.i need to know how can i lock my username for a time more than a month from my access not managerial access?
| User | Helpful Count |
|---|---|
| 110 | |
| 79 | |
| 79 | |
| 74 | |
| 59 |
