Activity in Technology and Support
Cisco Secure Client CVE-2024-20337
Following upgrading to upgrading to 5.1.2.42 to fix the vulnerability CVE-2024-20337Within Microsoft Defender this is still flagged as vulnerability for the CVEIt appears to refer to a component of the install:C:\Program Files (x86)\Cisco\Cisco Secur...
Site-to-site vpn failover causing memory spike in spoke sites
Hi All. I would like to get your thoughts on the following issue i have been facing since implementing Dual ISP and failover for site-to-site vpn tunnels.Hub Site:ASA5515 using 9.6(4)42Spoke sites:Cisco ISRs using 15.1(4)M8, using voip services over ...
Max number of licenses available for Cisco ISE
I'm speaking of Essentials/Advantage/Premier. We use on-prem SSM.is there way to know how many licenses Cisco ISE gets from the binding to a virtual account on Cisco SSM?The only piece of information is the consumed ones, like knowing how many you ar...
optional variables in sdwan cli template
Is it possible to mark a variable as optional in sd-wan cli template?Can we use variables in a local data policy? I want to apply an ACL to internet facing interface that only permits traffic to the internet facing IP only. Policy will be applied to ...
Increase TX buffer size exanic x25
I have a exanic x25 I wanted to know how and from where can we increase this size of the tx buffer. Any help or suggestio?
Call Handler Not Reachable From Outside Call
Hi Experts,I am sitting with an unique issue where my Auto Attendant works perfectly from inside the office, however it is not reachable from external calls.Connection ISP > SIP > CUBE > SIP > CUCMWhat I am seeing is as soon as I direct the call to C...
The operation took longer than expected.
I have just synchronized both Active Directory and Cisco ISE, ISE is using my server (AD) as an NTP server, everything is fine, but now I'm facing an issue "Status Summary: The operation took longer than expected. This may be caused by slow network c...
Resolved! How to do VLAN mapping per Flex Profile on a 9800 WLC
Hi,I have a Flex Connect design on a new 9800 WLC.I would like to know if I can have a different VLAN ID per SSID like the AireOS FlexConnect Group - WLAN VLAN mapping. In my design the Flex Profile is equal to a Branch Office. So I would like to con...
Cannot turn on 8841 phone
Hi all. In the screenshot I encountered a problem: immediately after turning it on, this appears. Has anyone else encountered this problem? It asks for a domain, username and password. The phone is completely new. There is a way to access the setting...
VPN route-based unable to ping remote IP
Hi, I am currently encountering issue on route-based ipsec vpn. I cannot ping my remote IP also the remote tunnel. I have verified that there is no decap showing on packets. I already configured static route between each site and still unsucessful of...
Resolved! Best practice lan configuration
HiI have 4 Cisco 2960 switches and 3 unmanaged switches. All are connected via fiber cable to a core switch 4503-3 and it is connected to a VPN router and internet router. (still don't have access to the routers yet)I know I have to replace the unman...
Service impact on ISE certificate renewal
Hello. I'm trying to renew the ISE's certificate, but I'm using both admin and eap authentication, portal, and radius DTLS. In this case, I would like to know if renewing this certificate will reboot the ISE or if it will cause downtime. The certific...
Cisco SD-WAN prefix list & data prefix list update
Wanted to understand the best practices when updating the prefix-list & data prefix list in SD-WAN network.For example I have the below prefix-listlist_abc: 10.10.10.0/24This prefix list has been used in Centralized policy.I wanted to added new subne...
Configure Port-channel and vPC in advance in Nexus 9K
hi,i'll be configuring a new N9K switch to replace a C9300.my question is, can i configure in advance the port-channel and vPC in the N9K even without the SFP inserted and fiber cables patched?just want to prepare the config so it will be a faster to...
Not able to activate any service on CUCM Subscriber
Hi all, I am not able to activate any service on subscriber and it shows me database failure, when I enter "utils dbreplication runtimestate" on publisher it shows me defining for the subscribers. Can someone help me in both issues?
| User | Helpful Count |
|---|---|
| 109 | |
| 107 | |
| 86 | |
| 69 | |
| 61 |
