Activity in Technology and Support
NTP and Syslog packets with specific IP Address
Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...
Cisco API EOX Access getting status code: 403, reason: Forbidden
I am user with customer administrator role but still unable to get access to EOX API . When in try API request I get eh below 403 Forbidden error. Do let me know if any other details is needed.
Catalyst 1300 Dynamic ARP Inspection causes IPv6 performance issue
Hello,I have a C1300, I use it as my IPv4 and IPv6 gateway for internal routing. It has a default gateway to another router for internet access. If I perform an IPv6 speedtest with the c1300 as my gateway for IPv6 then I get around 1Mb, this is stran...
FTD re-register to FMC chassis mode
Deployed a 3100 in chassis mode to the FMC a few days ago. All went to plan.Determined we needed to change the IP so decided just to delete the device from FMC and re-provision it.On the FTD via local-mgmt did a erase configuration. The device wiped ...
UCCX CUIC - SMTP From address for e mailed reports
Where does one set the FROM e mail address used by CUIC report scheduler to e mail reports? I thought I knew....but it isn't where I thought it was. And I cannot find it in any documentation....
Resolved! C9120AXI-E EWC license
Hi,if I want to use 2 x C9120AXI-E with Embedded Wireless Controller for redundancy what license do I need? regards
Cisco 2960S not pinging, but has DHCP address
Hi,I am trying to set up an SSH connection to my switch, but right now there is some lower level problem. I have set up my FastEthernet0 interface to ip address dhcp and the command show interfaces FastEthernet0 shows the correct address. Even if I t...
VPN Tunnel connecting at a unconfigured setting - Phase 1 Timer
OK, so I've got a set of ASA's and we are migrating them to Firepowers, and all seems ok. In the past we have noticed that for some reason on the ASA's, no matter what you specify as the parameters for phase 1, the rekey timer always connects at 3600...
Resolved! Segment routing dynamic option
Hello Everyone, I am new to segment routing. I am trying to learn the dynamic option of segment routing traffic engineering. I have 2 directly connected routers.R1---R2R1's Gi0/0/0/1 IP address 100.10.20.1R2'2 Gi0/0/0/1 IP address 100.10.20.21.1.1.1 ...
Resolved! Catalyst 9500-16X
Hello everyone,I am a student, and for a paper i am doing i was wondering if Catalyst 9500-16X was able to do VPN IPSEC as a client, connecting to a cloud VPN IPSEC server. The use case is a Collapse Core topology and i would use 2 C9500-16X as the c...
Cisco 9200L : NAC behaviour with dynamic vlan assignement dead server
Hi all,I want to ask you experts some suggestion on how really work mechanism between Cisco switches and radius server when using dynamic vlan assignement and the radius suddenly will be unavailable.With server dead command under port configuration i...
Cisco ISE cannot join Windows Server Core.
My Windows Server Core having an internal address of 192.168.50.2, when natting it (NAT) it has an address of 192.168.99.36 (I'm installing Windows Server Core image on an EVE-NG VM and the EVE-NG VM is installed on ESXi).I have a Cisco ISE VM instal...
Cisco WSA log shows 503 status code
Hi we have 2 WSA out of which one WSA is showing 503 error for a specific Site. When i tried nslookup in WSA for that site it shows the server returned no data(in both WSA).But the site is working in one WSA but not in the other and after 15 mins the...
FMCv 7.2.5.1: High CPU load - how to troubleshoot?
Hello everybody,our customer has a FMCv running sugg. rel. 7.2.5.1 and has a high CPU load of approx. 97%.(see attached screen dump).The VM has 4 CPUs, 32GB RAM and 250GB HDD.The FMC is managing a HA of two Firepower 1120 running rel. 7.2.5.A FMC reb...
Temporary loss of WIFi connection between handheld terminal and AP
Hello,We got new terminals Honeywell EDA61K, but we have a problem with connection loss.Wireless LAN Controller is Aironet 2800 Series ME. Terminals randomly lose connection. After a while he returns.I switched the WiFi network only to 2.4. This redu...
| User | Helpful Count |
|---|---|
| 114 | |
| 110 | |
| 86 | |
| 64 | |
| 62 |
