TelePresence and Video Infrastructure

vg 224 fax receive intermittant smudged lines

We have a vg 224 configured as sccp to connnect to fax machine and the incoming PRI was controlled by Cucm 8.5 via MGCP. And tried all combinations, the RICOH machine still gets smudged lines intermittantly. Here is the configuration of vg224. Please...

Search Rules for VCS

Hi,I just to find out if someone can point me to documentation that can guide me to configure search rule in VCS?Krgrds,Kay Leong

Resolved! E20 API

Hi.I am trying to change the system name in the webinterface of the E20 with the following command: http://address_of_codec/formputxml?xmldoc=<Configuration><SystemUnit><Name>NewName</Name></Configuration></SystemUnit>but I get a 500 - Internal Se...

TMS Provisioning Directory in Phonebook

I'm having a problem where the only provisioned users that are showing up in the phonebook are users that have an associated device. Shouldn't all users that are provisioned show up in the phonebook? Is there any way to modify this behavior?For exa...

Resolved! TMS Phonebook against LDAP Directory

Morning,we plan to use a real LDAP Directory as Phonebooksource.To connect via the AD it' no problem, but the user at LDAP has another format.AD : <<domain>>\<<username>>LDAP : CN=videoUnit,CN=Abo,CN=Accounts,CN=System,CN=Apps,O=company,C=DEAt this f...

Tandberg VC units and PRI lines?

Hi Folks,I am slightly confused on this topic so please bear with me...Heres my dilemma: We have a number of Tandberg VC units (Profile 42, EX90 etc) that currently can do IP calls only as they are all registered to a TMS. If I wanted to connect a PR...

basic voip setup

my experiance with voip is very lessi have a requirement to suggest a basic VOIP soltion .at present there are 4 analog phones connected to a pabx. this system shoul be connected to a BASIC ip phone which will use by operatorwhat r the required equi...

Without 'MLS QOS' in 6500 does any interface queueing and trusting take place?

I have a 6500 that does not have 'mls qos' global configured, although the interfaces do have 'mls qos trust dscp' on them as in:interface GigabitEthernet3/3switchportswitchport access vlan 536switchport mode accessswitchport voice vlan 910logging ev...

Tandberg T3 and TP7010 issue

Our Tandberg T3 system can dial into our conferences on our TP7010 server and stay connected with the welcome screen on all three codecs indefinitely. As soon as a second party joins the conference on the TP7010 (doesn't matter if it is a CTS or H.3...

Resolved! VCS and AD ports

Hi All,I'm trying to use the AD autentication for movi user. My VCS Control is in DMZ and the AD server is on LAN.the question is: wich ports are used by VCS to connect with AD?I have already read the: "Authenticating Devices Deployment Guide Cisco ...

Resolved! CTM together with TMS in a Demo

Dear allWe have the follow Demo in our Office:CUCM 8.6.2 <-> SIP trunk to VCS 7.02CTS1300TSM 13.1.2C-Codec'sMXP'sCTM 1.5 (will be upgrade to latest)Is it possible to us in a DemoLab CTM 1.8 together with TMS 13.X ?I have now running succesfully TMS ...

Resolved! VCS Lync integration over TCP

Hello. I have followed this guide to enable integration between Lync and Cisco VCS:http://www.cisco.com/en/US/docs/telepresence/infrastructure/vcs/config_guide/Cisco_VCS_Microsoft_Lync_2010_Deployment_Guide_X6-1.pdf. I am trying to enable Lync to ...

Resolved! Tandberg 990 MXP TTC7-08. Factory default settings

Hi everybody !I have some problem with Tandberg 990 MXP TTC7-08, I’m trying to reset this device, but I don’t know how to do this with remote control.Can someone help me ?

IP dialling to a MCU (codian) registered to a gatekeeper (VCS)

So I have been racking my brain trying to figure out an issue that I am having.I am trying to figure out why I cannot dial to the IP address of my codian bridge when it is registered via H.323 to my VCS controller.I can dial to any endpoint registere...