Ip Phones in CUCM 4.2 give me this message in display, sometimes. What maybe the possible causes ?
Ip Phones in CUCM 4.2 give me this message in display, sometimes. What maybe the possible causes ?
Hello peeps!I'm wondering who would I classify IP SLA packets?I have ip sla going from 192.168.1.1 to 192.168.1.2Voice, ftp and streaming are all classified and LLQ in placeBut IP SLA fails because of high volume on the serial line
Hi,When TelePresence is integrated with Microsoft OCS Client (MOC) ,1. Does presentation sharing work both ways ?2. What is the user experience for the MOC user ? ( i.e. how does a MOC user connect to a multiparty TP meeting )3. Can a MOC user direc...
Hi,does anybody know when CUCM 8.0 will be supported by CTS? Current release notes end up with CUCM version 7.1.3.Thanks and regardsGundolf.
Hello guys!I going to write a examination work about something technical in the Network branch. I found it hard to find something to write about but yesterday when i watched "24" on the tv, they used cisco to have video conference. I think it must h...
Hello, I recently implemented CUVA into our enviornments and I had a fewquestions.We have a Cisco Call Manager version 4.1. The other day I found that if I install CUVA (and the camera) on a computer and enable video capabilities for the device, we c...
The quesition is,- The current link is 20 Mbps, - a CTS-3000 must be implemented, Can I order to Carrier provide me addicional BW by burst ?, I meam, If the Video traffic be detected, more 15 Mbps will be available to premium traffic .Is it ...
hi,i have a problem with my new fresh CTSMAN installation. the problem is to discover ROOMs in CUCMthe connection to cucm is verified with a status OK, but can't discover any CTSes configured. CUCM is a standalone server - publisher.system log is: Un...
Hi,I have CallManager 5.X, with Gateway in H323 mode, an access PRI.I will add BRI card on this router, more than I will add 10 users in CallManager, I want that the calls external of these users uses just new BRI Card.These users have Partitions and...
Hi,We have two locations lets say A & B, for which the end-to-end delay is about 150 ms. If A has two endpoints (say A1, A2) and in B another two (B1, B2), and if we were to try a multipoint call between 3 of the endpoints, it seems that it is not p...
A users account was accidentally deleted and marked for removal on next LDAP sync. Is there anyway to recover the CUCM account and save from deletion?CUCM 7.1.3(a)
Hello guyz! need some expertise adviceI have 2 routers setupconnected via s0/3/0 ospf running1 cipc phone on R1Analogue phone R2dial peers setup all fineCodec = g711aBandwidth = 128DCE = 128000No QoSVery basic setup...Theory 1 G711a phone call = 95.2...
Hi, could you please tell me, can I use this module for connecting to PBX through PRI. And what does mean B in 2CE1B acronim. Thanks
I want to install NM-HDV2-1T1/E1 on Cisco 3725 for VoIP using E1 which will be conectted to PBX.But I am not sure which IOS Feature should be installed into 3725. ( current IOS is IP Plus)IP Service is Enough ? or Need an Advanced IP Service ?I tryed...
HiCan the CUVC 5100 series ( especially 5110 model) be used for HD interop with a Polycom end point ?What is the additional bandwidth required on a CTS endpoint for 720p HD interop ?Thanks
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
09-21-2023 06:21 AM | ||
09-13-2023 06:56 PM | ||
09-11-2023 06:20 AM | ||
08-31-2023 05:32 AM | ||
08-29-2023 03:45 PM |