I would like to connect a doorphone on my CCME system. Does Cisco have an IP doorphone? I didn't see one online, but wanted to make sure. Would I have to setup an ATA? I really need a simple installation since this is for my boss' home.Thanks,Dam...
I would like to connect a doorphone on my CCME system. Does Cisco have an IP doorphone? I didn't see one online, but wanted to make sure. Would I have to setup an ATA? I really need a simple installation since this is for my boss' home.Thanks,Dam...
Hi,We have recently migrated to new CallManager servers. Our Tanberg video conferencing units which previously were set up as H.323 devices now will not display on the new CCM's. On the old, the IP address showed up to show everything was working, bu...
I just bought a Tandberg 3000 MXP conferencing system, I understand that the codec came with this system can support up to 4 video and 3 audio streams. Can someone tell me if I can integrate the Tandberg 3000 MXP codec with CallManager as a video/aud...
Has anyone used the Cisco IP to IP Multiservice Gateway as a SIP Session Border Controller
Can anyone help us, we need to know that if the video stream fails on a call between 2 7985 video phones does the audio stream remain intact.
We have two Ip/TV boxes and they are just constantly flooding the local subnet with thousands of multicast packets. I wouldnt assume that would be the normal operation as this takes up a lot of bandwidth. Does anyone have an idea of the problem?
Can anyone tell me what are the minimum OS, Ram and CPU requirements for running IPTV Viewer 3.5.7.1? thanks.
HiOne of our clients would like to be able to show IP based Video Conferences on to the television set(s). Is there any solution by Cisco that can take IP/TV input and give the correct PAL/NTSC output, so that the conference can be shown on normal TV...
Router: 3725 This router is being used for porting call legs via POTS/Dial-peers. T1's controller at this router is terminated in a PBX. When call are originated via Channel Banks (TDM via on both routers) - calls are successfully connected (via GRE ...
we have had many requests for access to CCMUser from the internet so our users can turn on and off their call forwarding. I am somewhat hesitant to open any access to the Call Manager from the internet. What is everyone else doing to get around thi...
Hello,I have a problem with a MCU 3515. I can't make the EMP to register to MCU. The message received is:CONNECT: S_errno_ECONNREFUSED 73450 DEBUG2 MP MAIN |MP: Start Registration. MPI address is taken from Config file Ip: 192.168.0.3 Port: 201...
I'm trying to get VTA(s)to connect to a polycom MCU. I can call other Polycom VSX / PVX units with no problems, only the MCU is giving issues. I get to a mulit screen display wih VTA but then the MCU complains about a Video Sync Loss and neither en...
Hi,E1 line is connected to my Cisco AS5350....I want to originate the calls and send them to a SIP Server ....Any document that could help or the document where do I get the commands will be highly appreciated...
IP Communicator and Video Advantage 2.0(2). I have video enabled the IP Communicator in Call Manager and reset but can not get the Camera Icon to show up. Video Advantage indicates that it does not recognise that IP Communicator is present. Any idea...
We have started using the Transparent LAN Services (TLS) from our local ISP. We are running H.323 (384K) video over this link. The link is 9.2M, and we show an average traffic rate of approx. 2M in/out with MRTG 5 minute averages. We are experiencing...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-06-2024 09:05 AM | ||
10-04-2024 06:18 AM | ||
10-02-2024 07:36 PM | ||
10-02-2024 06:18 PM | ||
10-01-2024 08:17 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |