Dear sir,I have a module NM-HDV-2E1-60. That module need to be replaced. But the serial number of 'show diag' can't be recognized on SCC. Doesn't NM-HDV-2E1-60 have a serial number?Can anybody tell me something?Thanks very much.Sha
Dear sir,I have a module NM-HDV-2E1-60. That module need to be replaced. But the serial number of 'show diag' can't be recognized on SCC. Doesn't NM-HDV-2E1-60 have a serial number?Can anybody tell me something?Thanks very much.Sha
Dear allIs there a method to use the mrtg to monitor the gk current endpoint and current active call?any homepage or link will provide this information?Router 3620thx thx
ALLi very need to set the router which the traffic from which host, the traffic will pass through ip precedence 5, not by port level, is host level. which link i can refer, thx thx
Hi,I am trying to route international calls to specific gateways that are registered on my gatekeeper with prefix 00*. I issue the command zone prefix "local_zone" 00* gw-priority 10 "H323_alias1" "H323_alias2" and verify that the two gateways are re...
Hi Group,I am trying to find some information on Cisco Gatekeeper (MCM), and how it can be configured in a video over ip network.Any information at all would be appreciated, in particular configuration samples. Thanks
Hi,I have a vpn connection between two pix 501 in a lab environment. I am only getting one way video. Any ideas?Thanks
Hi, I have 3 routers that have the following connectivity:phone1---fxs<3620>E1----E1<3725>S0/0-------S0/0<2611xm>fxs---phone2The 3620 router has fxs and NM-HDV-1E1-30 modules. 3725 router has NM-HDV-1E1-30 & WAN modules. 2611xm router has WAN & fxs m...
I'm new to videoconferencing. How can i reserve permanently 256K of my E1 to my video sessions between nodes?. My router is a Cisco 3745 . I also have a Cisco 8400IGX administrering several E1's. thanx.
Hello Voice Guruplease help me to solve this problem. my Topology look like this:Phone -- PBX -- E1 qsig -- c3640 -- h323 -- c7206 -- E1 qsig -- PBX -- PhoneThe problem is that I can manually dial from phone to phone, but if you use the redial featur...
My problem :from carrier send to my network : - have calling ID --> translation profile (in AS5400 at dial-peer POTS) ---> xxxxxx : OK- Have no calling ID --> translation profile ---> xxxxxx : ISDN disconnect cause =1F .debug isdn q931 , have no Call...
I am trying to prioritize video traffic on an ATM IMA interface. I have configured the service policy class map,etc. I can't apply the service policy to the ima interface though. I tried under the pvc as well. When I apply it under the pvc, it doe...
Hi, A client of mine has some regular Video Conference system that connects to BRIs. He has alot of problems with these BRIs. He also has a Cisco 3620 with a PRI that he uses as a dial-in modem bank (RAS). His question is, is there any way of ...
Can i get a call from a PBX to a Call manager IP Phone and do a transfer without wasting 2 Timeslots ?I know it can be done with Qsig ( Does the callmanager supports that ? )
Callmanager 3.3.When we set up a shared line '500' for softphone users we get an engaged tone when we access this DN.If a 7960 is added to the shared line it rings but none of the softphones ring.
Hi all,I am new to IPTV configuration , I have cisco IP/TV 3423 Broadcast server with Release 3.0 , it has some hardware issue,i can't use it ,can I install the software on an Intel box ..PLS helpthanks in advance.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-25-2024 03:44 AM | ||
09-24-2024 11:38 AM | ||
09-24-2024 02:13 AM | ||
09-19-2024 12:06 PM | ||
09-09-2024 06:26 AM |
User | Count |
---|---|
3 | |
2 | |
1 | |
1 | |
1 |