cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1185
Views
0
Helpful
1
Replies

VWIC-1MFT-E1

gaoyang
Level 1
Level 1

1 VWIC-1MFT-E1 in 1760, get following error:

00:00:07: %E1T1_MODULE-3-INITFAILURE: Slot 0, Unit 0 initialization failure - Fi

rmware Download

00:00:07: %E1T1_MODULE-3-INITFAILURE: Slot 0, Unit 0 initialization failure - FP

GA & Firmware Download

00:00:07: %E1T1_MODULE-3-INITFAILURE: Slot 0, Unit 0 initialization failure - E1

T1 Init

but the 1MFT-E1 in PVDM on 3620 is OK

sys info:

Router#show diag

Slot 0:

C1760 1FE VE 4SLOT DV Mainboard Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 3.0

PCB Serial Number : FOC07210YGP

Part Number : 73-7167-03

Board Revision : A0

Fab Version : 04

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 16 41 03 00 C1 8B 46 4F 43 30 37 32

0x10: 31 30 59 47 50 82 49 1B FF 03 42 41 30 02 04 FF

0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Packet Voice DSP Module Slot 0:

Hardware Revision : 3.2

Part Number : 73-6726-01

Board Revision : A0

Deviation Number : 0-0

Fab Version : 03

PCB Serial Number : ICP054100G9

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 02

Number of DSP's : 1

DSP memory size(in kwords): 256

Type of DSP : TMS320C549

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 02 AC 41 03 02 82 49 1A 46 01 42 41 30

0x10: 80 00 00 00 00 02 03 C1 8B 49 43 50 30 35 34 31

0x20: 30 30 47 39 03 00 81 00 00 00 00 04 00 09 02 FF

Packet Voice DSP Module Slot 1:

Hardware Revision : 3.2

Part Number : 73-6726-01

Board Revision : A0

Deviation Number : 0-0

Fab Version : 03

PCB Serial Number : ICP060201DP

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 02

Number of DSP's : 2

DSP memory size(in kwords): 256

Type of DSP : TMS320C549

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 02 AD 41 03 02 82 49 1A 46 01 42 41 30

0x10: 80 00 00 00 00 02 03 C1 8B 49 43 50 30 36 30 32

0x20: 30 31 44 50 03 00 81 00 00 00 00 04 00 09 02 FF

WIC/VIC Slot 0:

E1 (1 port) Multi-Flex Trunk WAN daughter card

Hardware revision 1.0 Board revision B0

Serial number 0030437839 Part number 800-04475-03

Test history 0x00 RMA number 00-00-00

Connector type PCI

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 21 01 00 01 D0 71 CF 50 11 7B 03 00 00 00 00

0x30: 58 00 00 00 02 12 23 00 FF FF FF FF FF FF FF FF

Router#show ver

Cisco Internetwork Operating System Software

IOS (tm) C1700 Software (C1700-SV8Y-M), Version 12.2(8)YJ, EARLY DEPLOYMENT RELE

ASE SOFTWARE (fc1)

Synched to technology version 12.2(8.5)T

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Fri 21-Jun-02 13:14 by ealyon

Image text-base: 0x80008124, data-base: 0x81208FC4

ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)

ROM: C1700 Software (C1700-SV8Y-M), Version 12.2(8)YJ, EARLY DEPLOYMENT RELEASE

SOFTWARE (fc1)

Router uptime is 3 minutes

System returned to ROM by power-on

System image file is "flash:c1700-sv8y-mz.122-8.YJ.bin"

cisco 1760 (MPC860P) processor (revision 0x300) with 58983K/6553K bytes of memor

y.

Processor board ID FOC07210YGP (3803658949), with hardware revision 0000

MPC860P processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface(s)

32K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

1 Reply 1

ivillegas
Level 6
Level 6

It looks like the firmware for VWIC-1MFT-E1 loaded in the card is causing the failure.

Sugesstion is try with another IOS ver

check the no of chjannels used nad the DSP necessary to support it. If there is less no of DSP failure will occur