We are trying to setup a 128k ISDN call and am not able to see the second number from the far end endpoint. This is what I see on the gateway.16-08-05 13:00:06.21 |USER INFO|CALL SETUP|INFO|(323Adapter) CALL SETUP: From IP, Bearer Capability Rat...
We are trying to setup a 128k ISDN call and am not able to see the second number from the far end endpoint. This is what I see on the gateway.16-08-05 13:00:06.21 |USER INFO|CALL SETUP|INFO|(323Adapter) CALL SETUP: From IP, Bearer Capability Rat...
Two 3640's (12.2(24) are connected via a 7MB ATM PVC (cbr). I configured following policymap guaranteeing 900 kbps for Video-conferencing between Policom VSX7000's.policy-map VIDEO30-OUT class VIDEO-OUT priority 900 60000 class class-default fair-q...
Hi,Can someone tell me how to configure callmanager and 2600 gateway with DID card? Because DID Card (in DID mode) can only receive call, is there any configuration on callmanager?
1) When using CVP, is it possible to do flash hook transfers or is there a data interface to the ACD?2) Is integration with the Cisco CTI engine available and the ease with which this can be accomplished?3) What Telephony Card it uses ?
Is it possible to configure a back-to-back connection between two E1 port ?
The command really works in anolog ports(fxs,fxo) and R2 (E1). But it doesn't in ISDN PRI condition. and we have ".T" config. How can I shorten the dailing time? Adjusting the T302 timers isn't a good idea(but we must use it now).thanks for any sugge...
I got a CISCO IP/VC 3511 MCU and tried to upgrade, it because there were not all of the configurations available as shown in the administrator documentation.So I started the Upgrade Utility for the 3511 and it wrote failure: you have to restart manua...
Will VT advantage work with non Cisco webcam ? Is it nessesory to use Cisco made webcam?
Hi,I have a HP Fax which connecting to my vg224 and a 3745 router to ISDN. The fax report specify that the transimission level -10.2dB was too loud. Is there a way this can be adjustable at the VG 224 voice port? How? ThanksHenry
i have 2 call managers setup up connected to each other through a trunk. i have a 2 2611 routers acting as a gatekeeper hanging off of each call manager.i have 2 h.323 end stations hanging off of the gatekeepers. they register with the gatekeepers....
Hi,I have a setup which has the link as shown: Remote site A: (ISDN --Router [h323] -- VG224 [mgcp] -- Fax) and CCM at the central. everytime when fax from ISDN to my vg224 analog fax, I can see dial-peer 0 being match. This results the fax sometimes...
I have a WAN network with frame-relay link (bandwidth 256Kbps)and conected to one there is a Catalyst 3550 doing Inter-VLAN. the switch port conected to router is routing (no switchport) and all others ports of the switch are at VLAN 1 (default). The...
Hi,I am trying to get VoIP to work for long distance (+1)calls.I have the following scenario:CCM4.1-->gk--->gw<---IP Cloud---->IP Telephony service provider gkWhat I am trying to acheive is route long distance calls over IP to a service provider that...
I have 5 7912s running off of one switch that can call each other and everything works fine. But when I try to call out or in from a phone not on the switch the five phones can not hear anything. They are all running off the same call manager, and al...
Could someone let me know the difference between FXS and FXO with respect to a router, a PBX, a CO Switch, an analog phone, an ISDN phone?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
03-28-2024 08:12 AM | ||
03-27-2024 06:24 AM | ||
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 09:29 AM |