Resolved! Precision 60 standalone control
Hello, We have 4 x Precision 60 cameras and want to control them directly from a Crestron control system over Ethernet. Can this be done as I cannot locate any documentation supporting this? Thanks
Hello, We have 4 x Precision 60 cameras and want to control them directly from a Crestron control system over Ethernet. Can this be done as I cannot locate any documentation supporting this? Thanks
Hello,We have the room bar in each conference room, A touch panel on the table and a room scheduler on the outside of the room. We are wanting to add a wallpaper on the room scheduler. The touch panel and room scheduler are the same device but in dif...
With the world heading towards IP based everything in the very near future, it would be prudent for Cisco to begin to look at making one of the standard Audio over IP formats available as a way to input audio into the most advanced endpoints. Dante o...
Is CS-T10-WM-K9= still available to purchase?
Any help is appreciated. I have a SX20 we have running firmware version TC7.3.21. I want to get it on the latest CE firmware available for the SX20 Ce9.15.17.4What firmware if available can I use to perform the upgrade. I am pretty sure it will hav...
I have some confusion regarding MRA or sip proxy registration capacity in Expressway in SRND 14 https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/uc_system/design/guides/UCgoList.htmlthey mentioned small ova node supports up to 2500 proxy registra...
I've been trying to solve this problem for a really long time. I don't think it's ever worked.The Cisco Room Kit will after about 15 minutes go offline, be inaccessible on the network until someone walks into the room with it. Then it wakes up and is...
Hello community.I have a Room with 1 Codec Pro and 3 cameras - 1 quadcam and 2 Precision 60.I've conected their control ports and the codec control port into a switch, but I have camera control only for the quadcam.The speakertrack and presenter mode...
Currently our system allow you to connect to others with Zoom account or Point to Point connection. Is there a software update that allows us to connect to webex meeting on the touch panel? I don't see icons on the panel for use to use to connect t...
Hi All,We have a Cisco Cisco Webex Codec Plus that we need to enable ports for on the Cisco ISR 4300.Not sure if anyone has experience in this and what ports I need to allow (inbound and outbound) for Cisco Conference Room kit with Teams and Skype fo...
Hi, can SX80 add to a user in Webex Control Hub?If yes, does there any prerequisite? Like software type TC or CE? Must be what minimum version? Thank you!
Hi all, I'm trying to switch on or off a Philips TV by sending a CEC command through a Room Kit :xcommand Video CEC Output KeyClick LogicalAddress: 0 ConnectorId: 3 Key: 36 I read on CEC-O-Matic that the code 36 corresponds to off command or standby....
We have a Codec Pro K9 that I was working with and decided to attach a touch 10 to. I wanted to see if any more configuration options were available if a touch 10 was connected. The system does not have a touch 10. Now when I did a factory reset, it'...
I am ungodly new at this, so bear with me:I'm using Cisco xAPI to initiate a call into our Zoom meeting SIP number with the Dial command.After that call is initiated, I would like to retrieve the CallID from that call in order to pass it into other f...
Have WebEx meeting center hosted in cloud. CMR enabled. Would like to connect MCU to WebEx conferences. Endpoints can join and transmit DTMF to WebEx no problem. WebEx doesn't seem to hear DTMF from MCU, therefore, MCU can't join conference. I was di...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 01:51 AM | ||
03-11-2024 05:37 PM | ||
03-06-2024 10:37 AM |