Hi there
We have S4B interop using CMS spaces but really want calling between external S4B clients and internal Jabber users, using CMS as the gateway.
According to this lab (https://cmslab.ciscolive.com/pod2/edge/s4b) it requires a forward all ...
Afternoon community,
We're in the process of seeing if the DX80 will satisfy our STIG vulnerabilities. Where I seem to be stuck is with the network settings. We want to hide all instances of the IP address being displayed without a pin or password....
There’s no content sharing option and even HDMI cable is connected there’s no response.
Can someone advise what could be the issue ? Is it software version issue.
The software version i'm using is ce 9.1.2
Hi Team,
Was hoping that someone might have a nifty idea of how to approach an issue my team has run into while deploying a Room kit plus on CE 9.3.2.
We are using Panasonic TH-65PF50W monitors as we would like to life cycle them. Conferences conne...
I'm having trouble connecting our SX10 to our TV in our conference room. We are connecting it with an HDMI and PoE. No matter what HDMI input it is in, nothing shows up on the TV. It is a Vizio. Any troubleshooting suggestions are welcome. Thank you.
Hello,
We've had an issue with one of our conference rooms where the video/call seems to drop between the 40 minute to 44 minute mark when dialed into a WebEx to an outside party.
One of the logs I grabbed shows this:
2018-10-31 13:32:32 Use...
Hi everyone, does anyone have experience sharing offshore Acquisition and Seismic Interpretation content, which runs on 3d similar autocad software?My problem is that when i share these contents, in rendering, the image shakes a lot and if i do the s...
Hi;
I have a new deployment Exp C and E also trunk with CUCM for B2B calls but i've got failure like unsupported uri scheme.
My exp's software vers. 8.8.3 and my zone's are active between exp c and e also with cucm is looks active and ok.
I've ...
Hi Everyone,
First post here, hope it's in the right section.
We have installed around 30 Cisco Spark room kits (and 2 Spark Kit+). During installation, we ran HDMI cables from the Spark Kit to the desk of the room it was in. This was sometimes a...
I'm with Durham Public Schools and I have a location with a Tandberg C-series codec c20. Someone set a password and no one can remember what it is. It's for the soft pad that connects to the VC system and not the system itself although I understand ...
Any one out there having the following issue trying to SSH into a DX, MX, series Codec ???
CE9.1.3 version and CE8.2.3 version:
I use putty and see the login: than enter the admin and right after entering password, SSH disappears ???
This is happen...
I am running VCS 8.8.2 Control and Expressway.
Been working find. 99 percent of calls are H.323 calling via IP , and Alias.
Sometimes the DNS works I.e XXXX@cisco.com or XXX@tryacano.com etc.
Problem now is I only have a few Devices registered to ...
Hi everyone
Quick question is there a license that we have to purchase from Cisco in order to use the Hollywood squares view during a call with multiple participants on the EX60?
Hi, I have a Cisco Spark Kit Plus with a P60 Camera. When the camera is connected to the Camera HDMI interface on the codec, there is no video output. The codec complains that there is no video output on HDMI 1
If I connect the Camera to HDMI 2 or ...
Dear All,I have registered cisco spark room kit plus with CUCM, but I do not see registration status and IP address of the Codec in cucm. The status is none.Am I hitting any known bug?CUCM version: 11.5.1.11900-26SRK Version: ce 9.4.0 62bc0aa4505 201...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
