Hi, can you please tell me if the CTS-RMT-TRC6 can work with a TTC8-05 codec camera and CTS-SX20-CODEC with CE8 software version ? Best regards,
Hi, can you please tell me if the CTS-RMT-TRC6 can work with a TTC8-05 codec camera and CTS-SX20-CODEC with CE8 software version ? Best regards,
Hi, can you please tell me if the CTS-RMT-TRC6 can work with a TTC8-05 codec camera and CE8 verison software of a codec ? Best regards,
I'm trying to set up LDAP for CMS client login and am stuck on the login ID. The LDAP sync part works great for creating users and spaces so far, but I'm not sure I'm following how best to set up the field mapping to get a successful login from any o...
I am looking for some conformation / guidance on some QoS configuration. I have attached a diagram of the network example for what I am looking to do. I am looking at configuring QoS for IP Surveillance through a network. Now because the IP Camera I ...
GOOD MORNING I HAVE A MIC 60 THAT WAS CONNECTED TO AN MX800D AND THAT THEIR CABLES WERE CUT. MY QUESTION IS IT POSSIBLE TO GET A THIRD PARTY CABLE WITH ITS PHOENIX EUROBLOCK 4 PIN CONNECTORS AND OPEN THE MICROPHONE AND CONNECT THEM AND THE PHOENIX TO...
Hi All, We have two SX20 in two offices connected over P2P Link and working as standalone devices. Private IP's of both the SX20 are natted to the 2 different public IP addresses respectively. We want below call scenario. IP calling between these tw...
Hello, I'm running Expressway in Dual-NIC mode and I would like to block/disable the access to the management interface from LAN 2. As LAN2 is in the DMZ and we use Jabber Guest, port 443 is open on the firewall but translated to 9443 for Jabber Gue...
I'm doing an installation of two microphones mic 60 that left another technique unfinished. The problem is the following, they are two microphones for an MX800 device but it turns out they are without the phoenix euroblock 4 pin connector and the mic...
Hi, How are you? I have an Environment with tmsxe and Exchange 2010. We are using outlook form to booking conference by client. So, when booking is done the meeting is scheduled with no problem. But when the meeting is closed in client the notice is ...
Hi Is there a way to delete provisionioning datas on the VCSc when using TMSPE?I mean an option like "tmsagent_destroy_and_purge_data" but just for TMSPE? The reason I'm looking for that are duplicated directory entries on the e20 which I couldn’t so...
Hi All, I was reading about collab Edge configuration. I read then when we turn on Jabber it goes for UDS service , if the client is external it will fail and it will start looking for collab_edge service . After it gets the IP address for Exp-e c...
I am in the US Army and someone factory reset one of our MXP 1700 desktop Tandbergs. which deleted our New option key and New bandwidth key. the MXP 1700 have reached end of life and cisco will no longer support them. Does anyone know how I can get a...
Win Server 2008 R2 Standard. Cisco Telepresence Content Server 6.0.3528 Silverlight 5.1.50905 ERROR is: "Cannot play recording. An error has occurred." When trying to open a recording from with the content server, this error now occurs, for al...
Customer has a SX80 systems with dual cameras, engaging the speakertrack feature. The conference table in the room is shiny and has a very reflective surface. The cameras, during speakertrack use, have on many occasions dropped down from focusing on ...
Folks, i understand that CSCvc31381 effects SX80 codecs running CE8.2.2 but my concern is that this has been a known bug since December and it effects the "recommended" code version on the most important codec as its the heart and soul of integrated ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 01:51 AM | ||
03-11-2024 05:37 PM | ||
03-06-2024 10:37 AM |