Hi All,We are planning to use Session Border Controller (Cisco or Avaya) with MCU 5320, VCS, TMS.Could someone please provide SBC product that we can use with MCU? Thanks
Hi All,We are planning to use Session Border Controller (Cisco or Avaya) with MCU 5320, VCS, TMS.Could someone please provide SBC product that we can use with MCU? Thanks
Hello all,I'm trying to set QoS for Skype for business audio and video calls in ASA 5510.I've created priority queue on interface facing internet with settings:Queue Limit 2048Transmission Ring Limit 512And I proceeded to create Service Policy Rule o...
Hi all!Have you ever try to add a non-cisco device to the TMS?I'm now trying to add a Lifesize Team 220 to cisco TMS as a Meeting room and I get the System Not Found error message,The lifesize is reachable from the tms, but I'm not sure if the user/p...
After I spent a nice chuck of time writing a script to sync a custom TelePresence directory on our SX and EX TelePresence codecs using xCommand, I just received new DX70 and DX80 units which don't support the same xCommand controls. It's most likely...
I'm in the process of writing a script utilizing the xCommand API that generates a directory of our conference rooms in the local phonebook section of the SX codecs at my company. My end goal is to run the script nightly to wipe the local directory a...
I need to change the username from tandberg to admin. This unit is remote and I will use SSH. I am not sure what the command line is.
Hello, i've two problems C40 1. the video oh the camera do not display on the screen, (display black screen)2. when i connect the codec on the switch, it keeps rebooting, PS. he used to work perfectly, thanks everybody
We have several SX10's in our environment. I have 2 that are giving me issues. They are the only one's to have reported issues, not sure about the others. These 2 devices are setup identically and are in different buildings, on different switches,...
I have a Codian bridge running software version 4.4(3.57) . Connected to the bridge is an EX90 running software version TC7.2.1.cb31c3d. When the EX90 tries to control a far end point camera through the bridge using FECC commands, it works for a whil...
Hello.We have many C20 on 5.1.5 firmware and there are no problems to upgrade them to 7.3.2.But there is one C20 on 6.2.1 firmware. I can't upgrade it, it's stuck on "Running post-install hooks from installed package". I'll wait for 30-40 mins, but t...
Hi Everyone We have a lot of trouble with Release 7.3.2, ( touch panel 8 & so ) Does enyone now when next release is released ,?
Hi All,Is it possible to use (configure) Multiple TMS with different version on a Single VCS platform?If yes, is there any interoperability issues among MCU5320, TMS, VCS and ISDN Gateway? Thanks in advance Uddin
Hi Everybody, I have got 2 DX80 for testing and it works perfectly, the only things is sometimes it reboot itself without a reason. I have cheeked everything, even changed the active load for sipdx.10-2-2-33. As well as I have opened the RTMT during ...
I have a public IP connected to C-90 at customer location and he want the VC with other four or five location with different public IP . My question is how many outbound public IP's can C-90 dial and put all four locations in conference with out any ...
Hi all, Do you have any guides, information and suggestions about integrating CUCM with MCU, TCS and TMS?To centralized IPT and Video Conference enviroment, i need to register MCU and TCS to CUCM v10.5.Also TMS should provision devices which are regi...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-19-2024 05:00 AM | ||
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 01:51 AM | ||
03-11-2024 05:37 PM |