1486Hello all how calculate one interactive Video call bandwidth over MPLS networks Thanks
1486Hello all how calculate one interactive Video call bandwidth over MPLS networks Thanks
Hi All, I want to upgrade Telepresence content server Applianceright now they are running window server 20032003 is going to expire after 2 months that’s y they want to upgrade to 2008 Current TCS Hardware Configuration : Microsoft Window server 200...
Hello,what is the best solution for multivideoconferencing with Cisco.We have CP-9945, TPS500, Tandberg TX3000, CP-8945, Polycom HDX7000 , CUCM8.6 (that will be upgraed to 10)The goal is that there will be a conference bridge that is reachable from I...
I found another challenge on CUCM to dial URI with an IP-address as extension instead of domain name, e.g. room@172.30.12.13.In SIP Route Pattern you can define a IP-address or IP-address range with use of mask e.g. 172.0.0.0/8.But is there a way to...
Hello,Any help with this would be greatly appreciated. I'm aware you can run User CDR report in Cisco TMS, however, this pulls stats for ALL users within TMS. Is there a way to group certain users into a template perhaps to only run the report on th...
Hi!Trying to move from 5.3 (appliance) to 6.2 (virtual server). After running the migration tool (6.1) I realise there is no way to move the exported data directly to 6.2 in one go. Looks like I have to go via 6.0 first, however the 6.0 is not availa...
Hii've read Cisco TelePresence Content ServerRelease 6.0.x and 6.1 Administration andUser GuideAugust 2014 and tried to set up NAS with TCS.TCS(windows 2012 R2)---------------NASunfortunately, it was failed.So, i have a question.1. how can i set up s...
Hi all, Can't figure out how to configure SIP URI calls from/to SX codecs, registered on CUCM. I have CUCM and IM&P 10.5.1, a pair of Expressways X8.5.2 with two traversal zones - for B2B calls and the external jabber. I want to make calls from SX-co...
I have over 500 systems on TMS and numerous folders. How would I locate the folder a system is in by doing a system search rather than an I list??I performed a system search and it locates the system but doesn't tell me what folder it's in???Thanks....
I´m trying to configure a telepresence SX10, but it is showed the error above.Is there any way to configure without the SIP authentication? Error: Call Protocol RegistrationThe system is not registered on SIP. It will not be able to place or receive ...
Hello, we have a Cisco TelePresence SX20. We would like to know if it's possible to configure an IP blacklist, to block the H.323/SIP calls coming from specified IP addresses. TIA and regards.
Hello, we have a Cisco TelePresence SX20, connected to a Cisco TelePresence ISDN Link. We are looking for some working ISDN test sites (possibly in Europe, and with a loopback service, if they exist) to test our device. Which ones could you suggest t...
Can we safely upgrade directly or do we have to go via an intermediate version such as 1.8?Ip phone firmware is SIP70-8-5-3S to be upgraded to SIP70.9-3-1S
Hi all, Does CTS support ITL? It's supported by the IP Phones used by some CTS but, what about the CTS itself? Is it's supported, how can you delete the ITL to migrate the CTS between CUCM clusters? Thanks!
We have a conference coming up on 6/1 and it's been asked if we can have 1 specific video room connect an hour later than the rest. Is this possible? I'm in TMS and I'm not seeing options that granular. 2 rooms need to connnect at 10 but they want...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
03-28-2024 08:12 AM | ||
03-27-2024 06:24 AM | ||
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 09:29 AM |