We have large depolyment customer providing central VTC services (VCS/TMS/MCU/TCS/IPVCR/MOVI etc) to large mixed brand endpoint client base. Our customer does not have a say in what brand their clients select. Our customer would like to im...
We have large depolyment customer providing central VTC services (VCS/TMS/MCU/TCS/IPVCR/MOVI etc) to large mixed brand endpoint client base. Our customer does not have a say in what brand their clients select. Our customer would like to im...
I have a profile 52 dual and i am seeing excessive shiny spots where direct light falls, (people's forehead, cable on table). Are there any settings to fine tune this? I haven't made any changes to backlight, brightness, whiteness etc- all set to aut...
I couldn't seem to find it, although I fully admit I may have missed it in the install guide, I have a question about the feasibility of installing TMSXE on the same server as the TMS application.I do know that on page 9 the guide says that Cisco "re...
hello all, i have now encountered this issue 2x in 2 seperate customer environments. the promlem i am having is getting video to pass between CUCM and VCS when CUCM is on version 7.1.5. i have built a sip trunk according to the Cisco config guide (...
Hi.Two quiestions:1. All our video terminals are widescreen, and then you use MCU streaming, you get 4:3 video streamed, cut left and right borders. I did not find corresponding option in settings. Any suggestions?2. Is there ability to connect to co...
Hi ,I just wanted to know whether there are two different authentication credentials for XML- RPC call and for CLI access ?I cant get this info in docs which i have.Regards,Shankar
Hi,I've a problem using a TouchPanel paired to a C40 TC5.1 (issue also present in TC4.2) when I try to call to a contact (IP) shared by TMS (13.1).C40 is registered in a gatekeeper (gatekeeper mode), once I press over 'Call' an error appears:Cannot c...
Hi,I'm tasked with setting up a demo environment on a production client's network, we will just install 3 end points, most likelly SX20s for ease of deployment, my question is:What is the simplest and most effective scenario to deploy the units?They ...
I have a Tandberg 6000 Classic running E3.4 software, I know its very old.....We are working to get the system replaced with a C series Codec, but in the mean time we want to have the 6000 use the TMS Corp Dir phone books.We had several classics on t...
Do the C-series codec have the ability to switch camera preset based on microphone level? For example when mic 1 is receiving the strongest audio level then the preset 1 is activated, when mic 2 is the strongest then preset 2 is activated. ...
Hi eveybody,I am to a customer and I meet this error when I try to install a TMS software on a VMWARE ESX :Someone can help me plz
Hi all,As recent trend of CUCM & VCS integration, our office has followed the same to build a SIP trunk betweem CUCM & SIP. I have checked IPphone from CUCM side can call to video endpoint successfully, but there is loop detected on the call from vid...
Hi everybody, I have a question regarding the licenses of the VCS-C server which I bought for demo. I reset the server to factory default and all the licenses were lost . What should I do now in order to get the licenses back? The server's serial num...
Hi,Just thought I'd double check this, I suspect the answer is no - is there a way to disable content sharing (BFCP) on the Jabber client (without making changes on the infrastructure)?Thanks
Hello,we would like to test the integration between VCS X7.2 (VM version), CUCM 8.x and Microsoft Lync 2010, by only using the VCS demo licenses (for CUCM and Lync, we already have "real" licenses).Is it possible?TIA and regards.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-19-2024 05:00 AM | ||
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 01:51 AM | ||
03-11-2024 05:37 PM |