Hi,I have integrated a VCS and a CUCM and I am able to make calls between them. Now I am planning to add an MCU to this setup but I am not sure which solution is best. Should I register the MCU to VCS or CUCM or both?Regards,Tufan
Hi,I have integrated a VCS and a CUCM and I am able to make calls between them. Now I am planning to add an MCU to this setup but I am not sure which solution is best. Should I register the MCU to VCS or CUCM or both?Regards,Tufan
My company (Viettel, Viet Nam) uses Tandberg iPlex encoders for both IPTV and MobileTV service.In encoder's configuration, parameter Mode = Standard (3.0s). If IPTV user switches to a different channel, in first 3 seconds video and audio are not sync...
Hi,I'm having a hard time trying to reset a 7960 to factory defaults as per http://www.cisco.com/en/US/products/hw/phones/ps379/products_tech_note09186a00800941bb.shtml#topic1First I power on the phone and immediately hit "#"The instructions say that...
Hi there,I have a customer who needs two endpoints to call each other from one meeting room to the other over ip only.Does the Telepresence SX20 or other enpoints support this? Also do you have a config examples to register Telepresence endpoint to ...
I have what I hope is a quick question. My customer did not purchase the DNI option for their VCS Starter Pack. So, this means I have to assign a public IP address. Further, the way their firewall is provisioned I need to consider putting the VCS out...
Hi!Did somebody successfully try to move MXP/TC systems from one TMS to an other one?I am going to merge systems from two different TMS to one.I shortly tried to change the management IP for an endpoint, but the TMS then complained that its not its l...
We have an existing Telepresence infrastructure consisting of a Bridge / MCU (MSP200), Tandberg Gatekeeper, and approximately 20 Edge 95MXP endpoints. I would like to get two (and possibly more) EX60 endpoints incorporated into this infrastructure. I...
Hi all,We are planning to create 2 conferences at once on MCU by using it's API.But with xml below, only "Meeting 1" is created.Is there any syntax error?The model of MCU is MCU4510, SW version:4.3(2.18), andwe use "WizTools.org RESTClient 2.4" to ...
Hi, Can anyone tell me how to get the serial number of Tandberg Codec CTS-C60-K9 device.can this be located on the device and in what format is it written?Prompt response will be appreciated.Regards, Peter Nnaji.
Hello, I had a question about the Tandberg EX90, I'm trying to connect a projector in the HDMI Out of the Tandberg, but it is not giving signal to the projector, right now, what is it setup is this for the HDMI output: xConfiguration Video Output HDM...
we have a Tandberg MXP880 video conference device in the office that we've been using for more than 3 years now with ISDN connection and sometimes through LAN. Accepting video calls from one of our site in Japan is okay and having a 3 way video confe...
Im looking at the pros/cons when setting up CUCM 8.6 h323 or SIP trunk to Polycom CMA. Basically, I have a Polycom eviroment with different endpoints such as different V series endpoints (personal and conference room). I have CUCM 8.6 with diffe...
I am trying to get the CUCM directory to work on my EX60/EX90 endpoints. I am running TC5.0 on my end points and they are registered to a VCS. I have tried changing the phone book on the endpoints to use CUCM and I put in the standard directory URL...
I have several Cisco 7961G phone's that I'm trying to get setup with a CCM located in a separate geographical location. The CCM is attempting to push the SCCP 9.2.1 update to the phones which was taking forever and a day due to slow link connectivity...
Hi guys,a security audit (also in the video environment) brought up a "small risk" regarding SSL / TLS Renegotiation Handshakes on a VCS Expressway (X7.1).This VCS-E is a dual network port installation and the audit result relates to the test which w...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 01:51 AM | ||
03-11-2024 05:37 PM | ||
03-06-2024 10:37 AM |