Our IX units have their timezone set to "Current timezone: Australia/Sydney" which is UTC+10:00 but the logs appear to be in UTC+ 00:00. Can the log timezone be change? Software Version: 9.1.1
Our IX units have their timezone set to "Current timezone: Australia/Sydney" which is UTC+10:00 but the logs appear to be in UTC+ 00:00. Can the log timezone be change? Software Version: 9.1.1
I am using TMS with CMM. Is there a way to input DTMF tones?
I recently installed a new out of the box Codian 4220 Software version 4.1(1.51). I got it working with no visible issues. Then I sent to CISCO downloads and copied the 4.5(1.71) file. cisco_mcu_4200_4.5_1.71.zip. I also used the release notes and f...
Can HDMI output 3 of the CS-CODEC-PRO+ be configured to show ONLY the near end video currently selected by the TOUCH10 controller controlling the codec? Thanks
Currently we have Teams enabled meeting rooms. When I book a Teams meeting in either one of two particular rooms in outlook, I get the response back which says the meeting is accepted. Then about a minute later an email comes back and has the error: ...
Need a refresher please. I am at a new site running TMS 15.12.0. I need to pull reports over 90 period. When I run the report it tracks only for a week of data even when I set the start and stop date. What options should I increase in the log to k...
Anyone have a doc on steps to replace the SUPVR card with new one? Can it be done hot swap ? If not I assume take back up of config shut down the MCU swap the card power up remote in and restore config ? Thanks.
I've got a weird issue with a VCS-C cluster. I have two nodes running X12.6.2. Node 1 is a "cluster of 1" with itself defined as peer 1 (using IP address, everything set to permissive).When I add peer 2, they cluster OK and peer 2 grabs all its con...
Hello, We have a CMS recorder (version 2.8) which is configured successfully to save recordings into a shared NFS folder.We want to configure VBrick Rev/DME to read the files from the shared folder, delete them from there and save them on VBrick Rev/...
Hello, Can the Cisco Videoconferencing System (e.g. Cisco SX20 or Cisco Webex Room Kit) join an organized meeting on the V-CUBE platform? Thank you in advance for your support.
Hello, I'm running a single server deployment lab on VMware. Everything is running fine, but recording. I have done the following:1) Generated and issued internal CA certificates2) Configured recorder by CLI with certificates, listen to unbind port 8...
I have installed TMS 15.12 successfully after successful installation of SQL server 2016 express.on windows server 2012, java 8 as guide recommended, 2.8 net framework. but when i go for TMSPE v1.14 installation, it gives me a strange error.that it r...
We recently purchased a Spark Room 55. My IT provider said we have to use Webex to use device. We have outside providers that send requests from Teams, Zoom, etc. and we would like to view those meeting on the Spark Board. Is there a way to make this...
Running into an issue where all the accounts on both a CMS1K and CMS2K server are locked out, due to a misunderstanding of the CLI command user rule max_idle (was set as user rule max_idle 1). What can we do to regain access to these systems, or othe...
I am trying to find detailed documentation on the difference between the following products: Video Communication System - Control / ExpresswayExpressway - Core / Edge My understanding is that endpoints can register to both Control and Core.When used ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 01:51 AM | ||
03-11-2024 05:37 PM | ||
03-06-2024 10:37 AM |