cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Walkthrough Wednesdays
2326
Views
5
Helpful
7
Replies
Fred Nielsen (ePlus)
Rising star

"call send DTMF" on CTS

Anyone know the syntax for this undocumented CLI command?  Can't figure it out...

1 ACCEPTED SOLUTION

Accepted Solutions
Marek Tarnoci
Beginner

Hi,

SYNTAX:

call send DTMF {Arg0} {Arg1}

DESCRIPTION:

Arg0 - Mandatory

        Caller ID for which to send the DTMF signal

Arg1 - Mandatory

        DTMF signal to send

Example, here you are ...:

1. Initiate call:

admin:call start 112284021490001

2. after call is established check Call ID by command:

admin:show call status

          Call Status

Registered to Cisco Unified Communications Manager : Yes

Call Connected            : Yes

Call Type           : Audio-Only Call     Call Start Time    : Feb 19 09:39:27 2014

Duration (sec)      : 15                  Direction          : Outgoing

Local Number        : 112284031421006     Remote Number      : 112284021490001

State               : Answered           

Security Level      : Non-Secure          Call Id             : 3

3. Send DTMF by command:

admin:call send DTMF 3 53921568      

Sending dtmf signal...DONE

admin:                     

Regards

Marek

View solution in original post

7 REPLIES 7
Rafal Szeremeta
Cisco Employee

Hello Frederick

Sending DTMF tones from CLI or CTS GUI is not possible at the moment.

We have internal enhencement open for that.

Thanks

Rafal

Marek Tarnoci
Beginner

Hi,

SYNTAX:

call send DTMF {Arg0} {Arg1}

DESCRIPTION:

Arg0 - Mandatory

        Caller ID for which to send the DTMF signal

Arg1 - Mandatory

        DTMF signal to send

Example, here you are ...:

1. Initiate call:

admin:call start 112284021490001

2. after call is established check Call ID by command:

admin:show call status

          Call Status

Registered to Cisco Unified Communications Manager : Yes

Call Connected            : Yes

Call Type           : Audio-Only Call     Call Start Time    : Feb 19 09:39:27 2014

Duration (sec)      : 15                  Direction          : Outgoing

Local Number        : 112284031421006     Remote Number      : 112284021490001

State               : Answered           

Security Level      : Non-Secure          Call Id             : 3

3. Send DTMF by command:

admin:call send DTMF 3 53921568      

Sending dtmf signal...DONE

admin:                     

Regards

Marek

View solution in original post

Hi,

 

I have the same problem. I don't get the call ID and also the command didn't work when I tried with random call ID 1. Even the command 'call send DTMF' didn't seem to exist. Please confirm.

 

admin:call send DTMF 1 258903928

Executed command unsuccessfully
No valid command entered
admin:call send
Invalid Command
admin:call send DTMF 1 258903928

Executed command unsuccessfully
No valid command entered

 

admin:show status

Host Name    : SEP001DA238ABE7
Date         : Thu Apr 17, 2014 12:27:28
Time Zone    : IST
Locale       : en_US
Product Ver  : CTS 1.8.5(4) P1
System State : Run Normal
Boot Slot    : 1
Uptime:
 12:27pm  up 23 days, 20:50, load average: 1.69, 0.97, 0.76

Memory Total:         516180K
        Free:          17248K
        Used:         498932K
      Shared:              0K
     Buffers:         262416K

                        Total            Free            Used
Disk/ram              253871K          73166K         180705K (71%)
Disk/logging          107319K          83237K          18541K (18%)
Disk/factory           47104K           9852K          37252K (79%)
Disk/slot 1            47088K           5069K          42019K (89%)
Disk/slot 2            47088K           3248K          43840K (93%)


admin:show call status

          Call Status
Registered to Cisco Unified Communications Manager : Yes
Call Connected            : Yes

Call Type           : Audio/Video Call    Call Start Time    : Apr 17 12:25:30 2014
Duration (sec)      : 128                 Direction          : Outgoing
Local Number        : 39804               Remote Number      : 39822
State               : Answered            Actual Bit Rate    : 2250000 bps, 1280x720
Security Level      : Secured             Negotiated Bit Rate: 2250000 bps

admin:

Hi,

As I can see from status, you have obsolete version of CTS (CTS 1.8.5(4) P1). Upgrade your CTS, command is available from later version, I guess from 1.9.x

Regards.

Marek

.

Thank you

Video Admin
Beginner

Hello Everyone,

Do you know if there is an option to dial Lync conferences from CLI of CTS codecs?

I understand that the dtmf  works only from 1.9.x and above. Unfortunately i am running 1.8.X on my codec.

 

 

 

 

 

Content for Community-Ad

Spotlight Awards 2021