cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
190
Views
0
Helpful
1
Replies
Beginner

Radvison ISDN Gateway MCM Gatekeeper

Hi all,

I can't seem to get my Cisco Gatekeeper to work with my Radvision Gateway L2W? I can get the Gateway to connect to the Gatekeeper. The dial prefixes show up in the GATEWAY TYPE PREFIX TABLE. I cannot get a Polycom Via Video or Viewstation to dial the gateway thru the gatekeeper. If I dial the gateway via its h.323 name I see a response on the gateway, but when I dial the gateway prefix I get no response on the gateway. It seems that the gatekeeper is not forwarding calls to the gateway. Any help would be greatly appreciated.

Thanks,

flash:c2600-jsx-mz.122-17a.bin

GATEKEEPER ENDPOINT REGISTRATION

================================

CallSignalAddr Port RASSignalAddr Port Zone Name Type F

--------------- ----- --------------- ----- --------- ---- --

10.0.7.14 1820 10.0.7.14 61166 BWCGkPri H320-GW

H323-ID: GW235339786

10.0.7.14 1620 10.0.7.14 1619 BWCGkPri TERM

H323-ID: IVR235339786

Total number of active registrations = 2

GATEWAY TYPE PREFIX TABLE

=========================

Prefix: 9*

Zone BWCGkPri master gateway list:

10.0.7.14:1820 GW235339786

Zone BWCGkPri prefix 27* priority gateway list(s):

Priority 10:

10.0.7.14:1820 GW235339786

Prefix: 82*

Zone BWCGkPri master gateway list:

10.0.7.14:1820 GW235339786

Zone BWCGkPri prefix 27* priority gateway list(s):

Priority 10:

10.0.7.14:1820 GW235339786

Prefix: 85*

Zone BWCGkPri master gateway list:

10.0.7.14:1820 GW235339786

Zone BWCGkPri prefix 27* priority gateway list(s):

Priority 10:

10.0.7.14:1820 GW235339786

Prefix: 86*

Zone BWCGkPri master gateway list:

10.0.7.14:1820 GW235339786

Zone BWCGkPri prefix 27* priority gateway list(s):

Priority 10:

10.0.7.14:1820 GW235339786

Prefix: 87*

Zone BWCGkPri master gateway list:

10.0.7.14:1820 GW235339786

Zone BWCGkPri prefix 27* priority gateway list(s):

Priority 10:

10.0.7.14:1820 GW235339786

ip subnet-zero

!

!

ip host GW235339786 10.0.7.14

ip host BWCGkPub 198.30.10.29

ip host BWCGkPri 10.250.239.1

!

call rsvp-sync

proxy h323

!

interface Loopback0

ip address 10.250.239.1 255.255.255.0

h323 interface

h323 qos ip-precedence 5

h323 h323-id BWInternalProxy

h323 gatekeeper id BWCGkPri ipaddr 10.250.239.1

h323 t120 proxy

!

interface FastEthernet0/0

description proxy port 10.100.100.5

ip address 10.100.100.5 255.255.255.252

!

interface FastEthernet0/1

ip address 10.250.238.2 255.255.255.0

no ip proxy-arp

ip classless

ip route 0.0.0.0 0.0.0.0 10.250.238.1

ip route 198.30.10.29 255.255.255.255 10.100.100.6

no ip http server

dial-peer cor custom

gatekeeper

zone local BWCGkPri bw.edu 10.250.239.1

zone remote BWCGkPub bw.edu 198.30.10.29 1719

zone prefix BWCGkPri 001440826*

zone prefix BWCGkPri 27* gw-priority 10 GW235339786

zone prefix BWCGkPri 9*

zone prefix BWCGkPub *

no shutdown

1 REPLY 1
Highlighted
Cisco Employee

Re: Radvison ISDN Gateway MCM Gatekeeper

Use 9 as you gateway prefix with a speed selection of "auto"(so it supports all dialing speeds), take out the zone prefix 9*, and add a to the remote gatekeeper. This should fix your problem

CreatePlease to create content
Content for Community-Ad
August's Community Spotlight Awards