cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
6168
Views
5
Helpful
30
Replies
Highlighted
Enthusiast

Does your Jabber Client work

Does your Jabber Client work over Collab Edge?  Looks like you might be missing the external SRV records for _collab-edge._tls.

 

 

 

Highlighted

Sushant issue have been

Highlighted
Enthusiast

Hi Jreinmann Nice to here

Hi Jreinmann

 

Nice to here that MRA working with DX650.. I'm also looking to configure DX650 with Expressway 8.5. Can you please share if there is any guide which you followed for DX650 ?

 

Regds

Highlighted
Beginner

Strange! i have the MX

Strange! i have the MX registered via expressway and can make calls but cucm does not see it registered and i dont have the meeting icon from the UC profile. I feel darker things are afoot and telepresence/tms etc

 

Highlighted

Hi Peter, Are you sure you

Hi Peter,

 

Are you sure you selected MRA registration and not VCS-E based registration? Your MX can register directly to the Edge if that is a VCS in your case.

Highlighted
Beginner

Yes, the MX is registered

Yes, the MX is registered with Expressway E on the edge but this is proxied through the Vcs C to call manager. I upgraded to the very latest release of 10.5.2 and this resolved the registered status of the devices. I also have several remote workers using 8841 phones.

Highlighted
Beginner

I have a DX650, DX70, DX80,

I have a DX650, DX70, DX80, and SX20 ... I tested the DX650 to reg. to CUCM through CUCM, but I don't know where can I configure on that on DX650?

Highlighted
Participant

Theses statements are very

Theses statements are very confusing. What's the use of it?

Which version of DX650/DX70/DX80 will support MRA?

 

rgds, Geert.

Highlighted

Documentation indicates the

Documentation indicates the entire DX series will be supported.

 

I Too miss the option to configure this in either CUCM or endpoint software. I suspect the Expressway does have support now but the feature still needs to be released in the actual endpoint software versions.

Highlighted
Beginner

Hello All,I was wondering

Hello All,

I was wondering whether anyone has an update re firmware release on the DX endpoints to support MRA? We have been trying to get a DX80 to register via MRA, using Expressway 8.5(1) but it does not want to play nicely.

Current firmware version of DX80 is sipdx80.10-2-3-33.

Any thoughts / further information?

 

Highlighted
Enthusiast

Whilst the Expressway has

Whilst the Expressway has support for DX80 MRA, the code for the DX80 itself is not available yet, even in pre-release form, so for now there isn't much to do with them outside of the network without VPN.

Highlighted
Advocate

What I have seen is that

What I have seen is that firmware 10.2.4 will be needed for this. This is supposed to be available Q2CY15.

Please rate useful posts.
Highlighted
Beginner

Thanks George (and Martyn),I

Thanks George (and Martyn),

I'll contact our Cisco SE to see what they might know.

Highlighted

The info I got from Cisco

The info I got from Cisco recently is it will be supported in the q2 release DX endpoint software. A little more patience required than.

Highlighted
Beginner

Hi All,We have successfully

Hi All,

We have successfully used MRA with a DX80 but are now wishing to also use Extension Mobility on these devices. Does anyone know if this is supported? Whilst the "EM" option appears within the Settings menu, it has an error that the server cannot be reached. Therefore, I assume it is not tunnelled through MRA properly.

Any thoughts appreciated.

/David

CreatePlease to create content
Content for Community-Ad
Future of Work Virtual Summit Day 5

Cisco COVID-19 Survey

This widget could not be displayed.