キャンセル
次の結果を表示 
次の代わりに検索 
もしかして: 
cancel
1263
閲覧回数
0
いいね!
0
コメント
JapanTAC_CSC
Level 7
Level 7

2019年10月15日 (初版)

TAC SR Collection
主な問題

ASR9901 で dual rate port の port mode を 1G へ変更した際に、同じ NP に所属している変更対象外のポートが一度 flap する問題が報告されています。

RP/0/RSP0/CPU0:ASR9901(config)#hw-module location 0/0/CPU0 port-mode 4x10,4x1,16x10
# port 12-15 を 1G へ変更
RP/0/RSP0/CPU0:ASR9901(config)#
RP/0/RSP0/CPU0:ASR9901(config)#commit
RP/0/RSP0/CPU0:Aug 29 12:51:42.817 UTC: config[67789]: %MGBL-CONFIG-6-DB_COMMIT : Configuration committed by user 'cisco'. Use 'show configuration commit changes 1000000204' to view the changes.
RP/0/RSP0/CPU0:ASR9901(config)#
RP/0/RSP0/CPU0:ASR9901(config)#
RP/0/RSP0/CPU0:ASR9901(config)#
LC/0/0/CPU0:Aug 29 12:51:44.186 UTC: ifmgr[237]: %PKT_INFRA-LINK-3-UPDOWN : Interface TenGigE0/0/0/15, changed state to Down

LC/0/0/CPU0:Aug 29 12:51:44.186 UTC: ifmgr[237]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGigE0/0/0/15, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:44.186 UTC: ifmgr[237]: %PKT_INFRA-LINK-3-UPDOWN : Interface TenGigE0/0/0/14, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:44.186 UTC: ifmgr[237]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGigE0/0/0/14, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:44.186 UTC: ifmgr[237]: %PKT_INFRA-LINK-3-UPDOWN : Interface TenGigE0/0/0/13, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:44.186 UTC: ifmgr[237]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGigE0/0/0/13, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:44.186 UTC: ifmgr[237]: %PKT_INFRA-LINK-3-UPDOWN : Interface TenGigE0/0/0/12, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:44.186 UTC: ifmgr[237]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGigE0/0/0/12, changed state to Down
# 関連のない port 8-10 が link flap している
RP/0/RSP0/CPU0:ASR9901a(config)#LC/0/0/CPU0:Aug 29 12:51:45.621 UTC: ifmgr[237]: %PKT_INFRA-LINK-3-UPDOWN : Interface TenGigE0/0/0/10, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:45.621 UTC: ifmgr[237]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGigE0/0/0/10, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:45.663 UTC: vic_0_1[173]: %PLATFORM-VIC-4-SIGNAL : Interface TenGigE0/0/0/10, Detected Signal failure
LC/0/0/CPU0:Aug 29 12:51:45.673 UTC: ifmgr[237]: %PKT_INFRA-LINK-3-UPDOWN : Interface TenGigE0/0/0/10, changed state to Up
LC/0/0/CPU0:Aug 29 12:51:45.674 UTC: ifmgr[237]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGigE0/0/0/10, changed state to Up
LC/0/0/CPU0:Aug 29 12:51:45.874 UTC: ifmgr[237]: %PKT_INFRA-LINK-3-UPDOWN : Interface TenGigE0/0/0/9, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:45.875 UTC: ifmgr[237]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGigE0/0/0/9, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:45.926 UTC: vic_0_2[280]: %PLATFORM-VIC-4-SIGNAL : Interface TenGigE0/0/0/9, Detected Signal failure
LC/0/0/CPU0:Aug 29 12:51:45.936 UTC: ifmgr[237]: %PKT_INFRA-LINK-3-UPDOWN : Interface TenGigE0/0/0/9, changed state to Up
LC/0/0/CPU0:Aug 29 12:51:45.937 UTC: ifmgr[237]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGigE0/0/0/9, changed state to Up
LC/0/0/CPU0:Aug 29 12:51:46.148 UTC: ifmgr[237]: %PKT_INFRA-LINK-3-UPDOWN : Interface TenGigE0/0/0/8, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:46.148 UTC: ifmgr[237]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGigE0/0/0/8, changed state to Down
LC/0/0/CPU0:Aug 29 12:51:46.674 UTC: vic_0_2[280]: %PLATFORM-VIC-4-RFI : Interface TenGigE0/0/0/8, Detected Remote Fault
LC/0/0/CPU0:Aug 29 12:51:46.684 UTC: ifmgr[237]: %PKT_INFRA-LINK-3-UPDOWN : Interface TenGigE0/0/0/8, changed state to Up
LC/0/0/CPU0:Aug 29 12:51:46.686 UTC: ifmgr[237]: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface TenGigE0/0/0/8, changed state to Up


NP とポートのひも付きは、以下の show controllers np ports all コマンドで確認することが出来ます。

RP/0/RSP0/CPU0:ASR9901#show controllers np ports all

Node: 0/0/CPU0:
----------------------------------------------------------------

NP Bridge Fia Ports
-- ------ --- ---------------------------------------------------
0 -- 0 HundredGigE0/0/0/20, TenGigE0/0/0/10 - TenGigE0/0/0/11, TenGigE0/0/0/8 - TenGigE0/0/0/9, GigabitEthernet0/0/0/0 - GigabitEthernet0/0/0/7, GigabitEthernet0/0/0/12 - GigabitEthernet0/0/0/15, TenGigE0/0/0/16 - TenGigE0/0/0/19
1 -- 1 HundredGigE0/0/0/21, TenGigE0/0/0/24 - TenGigE0/0/0/25, TenGigE0/0/0/22 - TenGigE0/0/0/23, GigabitEthernet0/0/0/34 - GigabitEthernet0/0/0/41, TenGigE0/0/0/26 - TenGigE0/0/0/33

9901_portmapping.png

原因

本問題は 1G への設定変更時に対象外のポートを誤って reset してしまっていたことがことが原因であり、 CSCvr12506 として報告されています。
CSCvr12506 ASR9901 port-mode change for a group cause other group's ports flap

解決策

この問題の回避策はありません。
問題の解決には CSCvr12506 の修正されたバージョンを使用する必要があります。

備考
本不具合は、Bug Search Tool でも確認できます。
各製品の TAC SR Collection の一覧は、よくある質問と解決方法 (TAC SR Collection) から確認できます。

Getting Started

検索バーにキーワード、フレーズ、または質問を入力し、お探しのものを見つけましょう

シスコ コミュニティをいち早く使いこなしていただけるよう役立つリンクをまとめました。みなさんのジャーニーがより良いものとなるようお手伝いします